During a thin-walled workpiece's milling, its surface quality is greatly affected by chatter. Chatter free condition can be obtained if the milling stability is predicted before practical machining. Here, a milling stability prediction method was proposed based on the radial basis function approaching theory. The cutting force coefficients and modal parameters of the AL2A12 thin-walled workpiece were acquired with cutting tests and hammer tests, respectively. The state transfer matrix of the milling system was deduced with the proposed method, and the stability lobe diagram was determined with Floquet theorem. In order to verify the computational efficiency of the proposed method, the same system parameters were used in different methods. Compared with the zeroth-order semi-discretization method and the full-discretization method, it was indicated that the proposed method has the highest computational efficiency under the premise that the stability lobe diagrams obtained with different methods are coincident. Then, the AL2A12 thin-walled workpiece was machined with the given spindle speeds and axial cut depths being corresponding to the four points selected from the predicted stability lobe diagram. The effectiveness of the proposed method was verified through comparing the machining results with the prediction ones. The practical machining showed that better machined surface can be obtained with higher spindle speed when the axial cut depths are close to each other, the milling tool sticky phenomenon can also be avoided with higher spindle speed.
闫正虎,刘志兵,王西彬,刘彪,王东前. 基于径向基函数的AL2A12薄壁件铣削稳定性研究[J]. 振动与冲击, 2017, 36(3): 202-208.
YAN Zhenghu, LIU Zhibing, WANG Xibin, LIU Biao, WANG Dongqian. Milling stability prediction of AL2A12 thin-walled workpiece based on radial basis functions. JOURNAL OF VIBRATION AND SHOCK, 2017, 36(3): 202-208.
[1] 刘强,李忠群. 数控铣削加工过程仿真与优化-建模、算法与工程应用[M]. 北京: 航空工业出版社, 2011.
[2] Schmitz T L. Chatter recognition by a statistical evaluation of the synchronously sampled audio signal [J]. Journal of Sound and Vibration, 2003, 262(3): 721-730.
[3] Quintana G, Ciurana J, Teixidor D. A new experimental methodology for identification of stability lobes diagram in milling operations [J]. International Journal of Machine Tools and Manufacture, 2008, 48(15): 1637—1645.
[4] 毛汉颖,刘畅,刘永坚,等.混沌特征量识别切削颤振的试验研究[J]. 振动与冲击,2015,34(16):99-103.
MAO Hanying, LIU Chang, LIU Yongjian, et al. Experimental study on the identification of cutting chatter based on its chaotic characteristics [J]. Journal Vibration and Shock, 2015, 34(16): 99-103.
[5] Altintas Y, Budak E. Analytical prediction of stability lobes in milling [J]. Annals of the CIRP, 1995, 44(1): 357-362.
[6] Merdol S D, Altintas Y. Multi frequency solution of chatter stability for low immersion milling [J]. Journal of Manufacturing Science and Engineering, 2004, 126(3): 459-466.
[7] Bayly P V, Halley J E, Mann B P, et al. Stability of Interrupted Cutting by Temporal Finite Element Analysis [J]. Transactions of the ASME, 2003, 125(2): 220-225.
[8] Insperger T, Stépán G. Updated semi-discretization method for periodic delay-differential equations with discrete delay [J]. International Journal for Numberical Methods in Engineering, 2004, 61(1): 117-141.
[9] Wan M, Zhang W H, Dang J W, Yang Y. A unified stability prediction method for milling process with multiple delays [J]. International Journal of Machine Tools and Manufacture, 2010, 50(1):29-41.
[10] Eksioglu C, Kilic Z M, Altintas Y. Discrete-Time Prediction of Chatter Stability, Cutting Forces, and Surface Location Errors in Flexible Milling Systems [J]. Journal of Manufacturing Science and Engineering, 2012, 134(6): 061006.
[11] 李中伟,龙新华,孟光.基于Magnus-Gaussian截断的铣削系统稳定性的半离散分析法[J]. 振动与冲击,2009,28 (5): 69-73.
LI Zhongwei, LONG Xinhua, MENG Guang. Stability analysis of milling process by semi-discretization method based on Magnus-Gaussian truncation [J]. Journal Vibration and Shock, 2009, 28(5): 69-73.
[12] Ding Y, Zhu L M, Zhang X J. A full-discretization method for prediction of milling stability. International Journal of Machine Tools and Manufacture [J]. 2010, 50(5): 502-509.
[13] Wang M H, Gao L, Zheng Y H. Prediction of regenerative chatter in the high-speed vertical milling of thin-walled workpiece made of titanium alloy [J]. International Journal of Advanced Manufacturing Technology, 2014, 72: 707-716.
[14] Tang A J, Liu Z Q. Three-dimensional stability lobe and maximum material removal rate in end milling of thin-walled plate [J]. International Journal of Advanced Manufacturing Technology, 2009, 43(1-2):33-39.
[15] Song Q H, Ai X, Tang W X. Prediction of simultaneous dynamic stability limit of time–variable parameters system in thin-walled workpiece high-speed milling processes [J]. International Journal of Advanced Manufacturing Technology, 2011, 55:883-889.
[16] Wang M H, Lei G, Zheng Y H. An examination of the fundamental mechanics of cutting force coefficients [J]. International Journal of Machine Tools and Manufacture, 2014, 78:1-7.
[17] 汤爱君. 薄壁零件铣削加工三维稳定性及参数优化[M]. 北京:国防工业出版社,2014.