Research on Dynamics of Wheel-rim Reducer Used in Electric Vehicle Considering Gear Teeth Modifications
SONG Chao-sheng1, 2，WENG Yan-xiang2，ZHU Cai-chao1，XIANG Chao1，LIU Huai-ju1
1 The State Key laboratory of Mechanical Transmissions, Chongqing University, Chongqing 400030, China
2 Hangzhou Advance Gearbox Group Co. Ltd., Hangzhou 311203, Zhejiang, China
Abstract：The objective of this research is to reveal the mesh characteristics and dynamics of wheel-rim reducer used in electric vehicle considering gear teeth modifications. Three types of strategiesfor the tooth modification were proposed. And the contact patterns for the related gear pairs were calculated based on the systematic mesh model considering the tooth modification strategies. Then a multi-body dynamic model for the geared rotor system in wheel-rim reducer were setup using lumped parameter method consideringthe mesh stiffness and transmission error excitations. The dynamic mesh force and acceleration responses of the equivalent bearing support were calculated. The results show that poor contact patterns with edge contact existed without teeth modifications. Independent linear relief and independent crowning relief along the axial direction for the high-speed gear pair can improve the contact patterns obviously. And linear relief with crowning relief along the axial direction and crowning relief or pressure angle modification along the profile direction for low-speed gear pair can improve the contact patterns obviously. For the proposed three types of strategiesfor the tooth modification can decease the transmission error, dynamic mesh force and the acceleration responses of the equivalent bearing support obviously both for the high-speed and low-speed gear pair. Finally, the gear tooth strategy linear relief with crowning relief along the axial direction and crowning relief along the profile direction was recommended to design the gears of wheel-rim reducer used in electric vehicle.
收稿日期: 2016-01-29
出版日期: 2017-10-15
引用本文:
宋朝省1，2，翁燕祥2，朱才朝1，向超1，刘怀举1. 考虑轮齿修形的电动车轮边减速器动态啮合性能研究[J]. 振动与冲击, 2017, 36(20): 254-260.
SONG Chao-sheng1, 2，WENG Yan-xiang2，ZHU Cai-chao1，XIANG Chao1，LIU Huai-ju1. Research on Dynamics of Wheel-rim Reducer Used in Electric Vehicle Considering Gear Teeth Modifications. JOURNAL OF VIBRATION AND SHOCK, 2017, 36(20): 254-260.
[1] Kang M R, KahramanA. An experimental and theoretical study of the dynamic behavior of double-helical gear sets[J]. Journal of Sound and Vibration, 2015, 350: 11-29.
[2] Hammami A, Del Rincon AF, Chaari F, et al. Dynamic behaviour of back to back planetary gear in run up and run down transient regimes[J]. Journal of Mechanics, 2015, 31(4): 481-491.
[3] Glover R. Design of high speed gears,low load gears for minimizing gear whine noise[C]. Proceedings of the ASME International Design Engineering Technical Conferences and Computers and Information in Engineering Conference, 2013, 5.
[4]Choi BJ, Yoon JH, Oh JE. A study on axle gear whine noise reduction with deflection test[J]. Proceedings of the Institution of Mechanical Engineers Part D-Journal of Automobile Engineering, 2012, 226(D2): 225-233.
[5] Koronias G, Theodossiades S, Rahnejat H, Saunders T. Axle whine phenomenon in light trucks: a combined numerical and experimental investigation[J]. Proceedings of the Institution of Mechanical Engineers Part D-Journal of Automobile Engineering, 2011, 225(D7): 885-894.
[6]Yang J Y, Peng T, Lim, T C. An enhanced multi-term harmonic balance solution for nonlinear period- dynamic motions in right-angle gear pairs[J]. Nonlinear Dynamics, 2014, 76(2): 1237-1252.
[7] Kahraman A,Singh R. Interactions between time-varying mesh stiffness and clearance non-linearities in a geared system[J]. Journal of Sound and Vibration, 1991,146(1): 135-156.
[8]王泽贵,裴质明,郝志勇,等. 汽车变速器齿轮啸叫噪声试验[J]. 浙江大学学报(工学版),2013,47(07):1307-1312.
WANG Ze-gui, PEI Zhi-ming, HAO Zhi-yong, et al. Experimental study on gear whine noise from transmission in vehicle[J]. Journal of Zhejiang University(Engineering Science), 2013,47(07):1307-1312.
[9]周益,曾一凡,王泽贵. 齿轮精度与变速器啸叫声控制的定量分析[J]. 噪声与振动控制,2012, (3):94-98.
ZHOU Yi, ZENG Yi-fan, WANG Ze-gui. Quantitative analysis for gear accuracy and the control of transmission gear whine[J]. Noise and Vibration Control, 2012, (3):94-98.
[10]王泽贵,周益,周观鹏,张磊. 变速器啸叫声与下线台架振动的相关性试验研究[J]. 振动与冲击,2012, 31(23):180-184.
WANGZe-gui, ZHOU Yi, ZHOU Guan-peng, ZHANGLei. Correlations tests for transmission gear whine and vibration of end of line[J]. Journal of Vibration and Shock, 2012, 31(23):180-184.
[11]郭栋,邓斌,石晓辉,施全. 国产轿车变速器啸叫噪声源的识别与控制[J]. 中国机械工程,2011, 22(18):2264-2267.
GUO Dong, DENG Bin, SHI Xiao-hui, SHI Quan. Identification and reduction of gear Whine Noise of Domestic Transmission[J]. China Mechanical Engineering, 2011, 22(18):2264-2267.
[12]于蓬,章桐,冷毅,郭荣. 电动车减/差速器振动特性分析及改进[J]. 振动与冲击,2015, 34(07):85-92.
YUPeng, ZHANG Tong, LENG Yi, GUO Rong. Vibration characteristics analysis and improvement of differential/reducer of electric vehicle[J]. Journal of Vibration and Shock, 2015, 34(07):85-92.
[13]SONG Chao-sheng, ZHU Cai-chao, LIU Huai-ju, etal. Dynamic analysis and experimental study of a marine gearbox with crossed beveloid gears[J].Mechanism and Machine Theory, 2015, 92: 17-28.
[14]ZHU Cai-chao, CHEN Shuang, SONG Chao-sheng, et al.Dynamic analysis of a megawatt wind turbine drive train[J]. Journal of Mechanical Science and Technology,2015, 29(5): 1913-1919.
[15]宋朝省,朱才朝,LIM Teik Chin,等. 小角度空间交错轴变厚齿轮传动啮合动态特性研究[J]. 振动与冲击,2012, 31(8):153-157.
SONG Chao-sheng, ZHU Cai-chao, Lim TC, et al. Time-varying mesh characteristics of beveloid gears with crossed axes and small shaft angle[J].Journal of Vibration and Shock, 2012, 31(8):153-157.
[16]PENG Tao. Coupled multi-body dynamic and vibration analysis of hypoid and bevel geared rotor system[D]. Cincinnati, University of Cincinnati, 2010.
