Indirect inverse sub-structure method for multi-point rigid coupling product packaging and transportation systems
MENG Tianya1, LI Mingyu1,GUO Dong2,WANG Jun1,3
1.School of Mechanical Engineering,Jiangnan University,Wuxi 214122,China;
2.Key Laboratory of Advanced Manufacture Technology for Automobile Parts Ministry of Education,Chongqing University of Technology,Chongqing 400054,China;
3.Jiangsu Key Laboratory of Advanced Food Manufacturing Equipment and Technology,Wuxi 214122,China
Abstract:In actual measurement process, spatial structures at coupling interface of a product packaging and transportation system are commonly complex to cause FRF at interface is difficult to measure. Aiming at this problem, the indirect inverse sub-structure method based on multi-point rigid coupling product packing and transportation systems was proposed. This method did not need to measure FRF at system’s coupling interface to directly obtain FRF of an unknown substructure (product or key component) at coupling point. Firstly, based on dynamic equations and the principle of linear superposition, relations between forces and displacements of a system and its substructures were established. Then, through matrix transformation, formulas of the indirect inverse substructure method were deduced to be applied in different rigid coupling product packing and transportation systems. Finally, lumped parameter models were established to verify the correctness of the proposed method. The results showed that the indirect inverse sub-structure method is feasible and has good application prospects in fields of packaging and transportation.
[1] 张元标.产品运输包装系统逆子结构分析方法研究[D].珠海:暨南大学,2013.
ZHANG Yuan-biao. The study on inverse substructure analysis method of product transport packaging system[D]. Zhuhai: Jinan University, 2013.
[2] Klerk D, Rixen D J, Voormeeren S N. General framework for dynamic substructuring: history, review and classification of techniques[J]. AIAA Journal, 2008, 46(5): 1169-1181.
[3] Zhen J, Lim T C, Lu G Q, et al. Experimental determination of automotive system response characteristics[J]. Journal of Passenger Cars: Mechanical Systems, 2001, 110(6): 1755 -1762.
[4] Zhen J. Development of a spectral‐based substructuring technique for modeling and vibratory response of complex vehicle structures[D]. Alabama:University of Alabama, 2000.
[5] Zhen, Jiantie, Lim, et al. Determination of system vibratory response characteristics applying a spectral-based inverse sub-structuring approach. Part I: analytical formulation[J]. International Journal of Vehicle Noise & Vibration, 2004, 1:1-30.
[6] Zhen J, Lim T C, Lu G Q. Determination of system vibratory response characteristics applying a spectral based inverse substructuring approach. Part II: Motor vehicle structures[J]. International Journal of Vehicle Noise and Vibration, 2004, 1(1-2): 31 -67.
[7] Lu G Q, Wang L, Dong K, et al. Error effects on identifying coupling dynamic stiffness of a mechanical assembly by indirect inverse substructuring dynamic analysis[J]. Advanced Materials Research, 2012, 562: 556-559.
[8] 王军.产品破损评价及其防护包装动力学理论研究[D].无锡:江南大学,2009.
WANG J. Theoretical study on product damage evaluation and protective packaging dynamics[D] Wuxi: Jiangnan University, 2009.
[9] 王军,王志伟,卢立新,等.多部件耦合包装系统逆子结构分析一般性理论[J]. 振动与冲击,2014,33(7):58-62.
WANG Jun, WANG Zhi‐wei, LU Li‐xin, et al.Generalized inverse substructuring method for multi-component coupled packaging system[J]. Journal of Vibration and Shock, 2014, 33(7): 58-62.
[10]王军,卢立新,王志伟,等.多级耦合系统界面动态特性预测的间接逆子结构理论[J]. 包装工程,2011,32(21):1-3.
WANG Jun, LU Lixin, WANG Zhiwei, et al.Indirect inverse substructure method for dynamic characteristic prediction of multi-level coupled system interface[J]. Packaging Engineering, 2011, 32(21): 1-3.
[11] Wang J, Hong X, Qian Y, et al. Inverse substructuring method for multi-coordinate coupled product transport system[J]. Packaging Technology and Science, 2014, 27(5): 385-408. Journal of Vibration and Shock, 2011, 30(9):174-177.
[12] Wang J, Wang Z, Lu L. Step-by-step decoupling method for inverse substructuring analysis of a three-component coupled packaging system[J]. Journal of Vibration and Control, 2013, 1077546313490185.
[13] Wang J, Sun G, Lu L, et al. General formulation of inverse substructuring method for multi-coordinate coupled system[J]. Advances in Mechanical Engineering, 2014, 6: 475128.
[14] Wang J, Sun G, Lu L, et al. Indirect inverse substructuring theory for coupling dynamic stiffness identification of complex interface between packaged product and vehicle transport system[J]. Packaging Technology and Science, 2015, 28(2): 141-155.
[15] Wang Z W, Wang J. Inverse substructure method of three-substructures coupled system and its application in product-transport-system [J]. Journal of Vibration And Control, 2011, 17(6): 943-951.
[16] Wang Z W, Zhang Y B. Dynamic characteristic analysis of refrigerator-truck transport system by using inverse substructure method[J]. Packaging Technology and Science, 2014, 27(11): 883-900.
[17] Wang Z W, Wang J. Inverse substructure method of three-substructure coupled system and its application in product-transport-system [J]. Journal of Vibration and Control, 2011, 17(6): 943-952.
[18]王军, 王志伟, 卢立新,等. 多部件耦合包装系统逆子结构分析一般性理论[J]. 振动与冲击, 2014, 33(7): 58-62.
WANG Jun, WANG Zhi-wei, LU Li-xin, et al. Generalized Inverse Substructuring Method for Multi-component Coupled Packaging System[J]. Journal of Vibration and Shock, 2014, 33(7): 58-62.
[19]王军, 卢立新, 王志伟. 产品破损评价及防护包装力学研究[J]. 振动与冲击, 2010, 29(8):43-45.
WANG Jun, LU Li-xin, WANG Zhi-wei. Product damage evaluation and protective packaging dynamics[J]. Journal of Vibration and Shock, 2010, 29(8): 43-45.
[20]莫愁, 陈吉清, 兰凤崇. 扩展工况传递路径分析方法改进[J]. 振动与冲击, 2015, 34(8): 129-133.
MO Chou, CHEN Ji-qing, LAN Feng-chong. Improvement of operational-X transfer path analysis method[J]. Journal of Vibration and Shock, 2015, 34(8): 129-133.
[21] 王启利, 王军, 孙中振等. 界面响应不可测的刚性耦合系统逆向子结构分析[J]. 振动工程学报, 2016, 29(4):603-608.
WANG Qi-li, WANG Jun, SUN Zhong-zhen, LU Li-xin. Inverse sub-structuring theory of rigid coupling system with incomplete measured data[J]. Journal of Vibration Engineering, 2016, 29(4):603-608.