动态加载率对巷道内裂纹扩展速度及动态起裂韧度的影响

摘要
图/表
参考文献(30)
相关文章 (15)

全文: PDF (1211 KB) HTML (1 KB)
输出: BibTeX | EndNote (RIS)

摘要在巷道的钻爆法掘进过程中，巷道围岩周围将诱发较多的径向裂隙。为了研究不同冲击载荷作用下巷道内裂纹扩展速度及起裂韧度的变化规律，采用落锤冲击试验机对裂纹巷道模型试件进行冲击加载，模型试件选用青砂岩制作。试验中，采用裂纹扩展计进行裂纹扩展速度及起裂时间的测定，对不同冲击高度下裂纹扩展速度及起裂时间进行分析；随后采用ABAQUS有限元程序结合试验-数值法计算巷道模型试样在不同动态加载率作用下的动态起裂韧度，并对起裂韧度的变化规律进行统计分析，得出如下结论：(1)巷道内预制裂纹的扩展速度随着动态加载高度的增加而增大，随后逐渐趋于稳定，实测裂纹扩展速度略小于0.38倍砂岩纵波波速；(2)巷道内预制裂纹的起裂时间，随着动态加载率的增加呈缓慢下降的趋势，降低幅度范围为50μs左右。(3)随着动态加载率的增加，巷道内裂纹的动态起裂韧度逐渐增大，上升趋势也逐渐加大。

	服务

	把本文推荐给朋友
	加入我的书架
	加入引用管理器
	E-mail Alert
	RSS
	作者相关文章
	周磊
	朱哲明
	董玉清
	应鹏
	王磊

关键词 ：巷道, 裂纹, 动态加载率, 裂纹扩展速度, 起裂韧度

Abstract：In the process of tunnel blasting excavation,blasting activities may induce radial cracks in the surrounding rock of tunnels.In order to investigate the propagation velocity and dynamic initiation toughness of cracks in a tunnel under different impact loads,impact experiments by using green sandstone tunnel models with a mode I crack were carried out by the middle-low speed drop weight impact test system.In the tests,the crack propagation velocity and crack initiation time were measured by crack propagation gauges (CPGs),and the measuring results were analyzed.The dynamic stress intensity factors were calculated by using ABAQUS code,and the dynamic initiation toughness under different dynamic loading rates was obtained by using an experimental-numerical method,and the property of initiation toughness was analyzed.The studying results show that: ① Crack propagation velocities increase with dynamic loading rates,and as loading rate is larger than a certain value,it gradually tends to be a constant value.Crack propagation velocity is slightly less than 0.38 times of the P-wave velocity of sandstone.② Crack initiation time decreases slowly with the dynamic loading rates,and the range of reduction is about 50 μs.③ As the dynamic loading rate increases,the dynamic initiation toughness increases gradually.

Key words： tunnel crack dynamic loading rate crack propagation velocity dynamic fracture toughness;

收稿日期: 2017-09-04 出版日期: 2019-02-15

引用本文:

周磊，朱哲明，董玉清，应鹏，王磊. 动态加载率对巷道内裂纹扩展速度及动态起裂韧度的影响[J]. 振动与冲击, 2019, 38(4): 129-136.
ZHOU Lei，ZHU Zheming，DONG Yuqing，YING Peng，WANG Lei. Effect of dynamic loading rate on crack propagation velocity and dynamic fracture toughness in tunnels. JOURNAL OF VIBRATION AND SHOCK, 2019, 38(4): 129-136.

链接本文:

http://jvs.sjtu.edu.cn/CN/ 或 http://jvs.sjtu.edu.cn/CN/Y2019/V38/I4/129

[1] 郭东明, 刘康, 胡久羡, 等. 爆生气体对邻近硐室背爆侧预制裂纹影响机理[J]. 煤炭学报. 2016,41(1):265-270.
GUO Dongming, LIU Kang, YANG Renshu, et al. Experimental study on the effect mechanism of the explosion gas on the precrack in the back-blasting of adjacent tunnel[J]. Journal of China Coal Society, 2016,41(1):265-270.
[2] 郭东明, 刘康, 杨仁树, 等. 爆破对邻近巷道背爆侧倾斜裂纹影响实验研究[J]. 采矿与安全工程学报. 2015,32(1):99-104.
GUO Dongming, LIU Kang, YANG Renshu, et al. Experimental research on the influence of blasting on the inclined crack in the back-blasting side of nearby roadway[J]. Journal of Mining and Safety Engineering, 2015, 32(1):99-104.
[3] 唐治, 潘一山, 王凯兴. 冲击地压巷道围岩支护作用动力学分析[J]. 岩土工程学报. 2015,37(8):1532-1538.
TANG Zhi, PAN Yishan, WANG Kaixing. Dynamic analysis of support for surrounding rock of rockburst roadway[J]. Yantu Gongcheng Xuebao/chinese Journal of Geotechnical Engineering, 2015, 37(8):1532-1538.
[4] 倪海敏, 茅献彪, 张春, 等. 冲击载荷对巷道稳定性的影响研究[J]. 煤炭工程. 2011,1(9):84-86.
NI Haimin, MAO Xianbiao, ZHANG Chun, et al. Study on Bumping Load Affected to Mine Gateway Stability[J]. Coal Engineering, 2011,1(9):84-86.
[5] WANG M, ZHU Z M, DONG Y Q, et al. Study of mixed-mode I/II fractures using single cleavage semicircle compression specimens under impacting loads[J]. Engineering Fracture Mechanics. 2017,177:33–44.
[6] 王蒙, 朱哲明, 王雄. 冲击荷载作用下的Ⅰ/Ⅱ复合型裂纹扩展规律研究[J]. 岩石力学与工程学报. 2016,35(7):1323-1332.
WANG Meng, ZHU Zheming, WANG Xiong. The growth of mixed-mode I / II under impacting loads[J]. Journal of Rock Mechanics and Engineering. 2016,35 (7):1323-1332.
[7] WANG Q Z, FENG F, NI M, et al. Measurement of mode I and mode II rock dynamic fracture toughness with cracked straight through flattened Brazilian disc impacted by split Hopkinson pressure bar[J]. Engineering Fracture Mechanics. 2011,78(12):2455-2469.
[8] WANG Q Z, YANG J R, ZHANG C G, et al. Sequential determination of dynamic initiation and propagation toughness of rock using an experimental–numerical–analytical method[J]. Engineering Fracture Mechanics. 2015,141:78-94.
[9] 杨井瑞, 张财贵, 周妍, 等. 用SCDC试样测试岩石动态断裂韧度的新方法[J]. 岩石力学与工程学报. 2015,34(2):279-292.
YANG Jingrui, ZHANG Caigui, ZHOU Yan, et al. A new method for determining dynamic fracture toughness of rock using SCDC specimens[J]. Chinese Journal of Rock Mechanics and Engineering，2015，34(2)：279–292.
[10] WANG X M, ZHU Z M, WANG M, et al. Study of rock dynamic fracture toughness by using VB-SCSC specimens under medium-low speed impacts[J]. Engineering Fracture Mechanics. 2017,181:52-64.
[11] ZHANG Q B, ZHAO J. Effect of loading rate on fracture toughness and failure micromechanisms in marble[J]. Engineering Fracture Mechanics. 2013,102(2):288-309.
[12] ZHANG Q B, ZHAO J. Determination of mechanical properties and full-field strain measurements of rock material under dynamic loads[J]. International Journal of Rock Mechanics and Mining Sciences. 2013,60(8):423-439.
[13] CHEN R, XIA K W, DAI F, et al. Determination of dynamic fracture parameters using a semi-circular bend technique in split Hopkinson pressure bar testing[J]. Engineering Fracture Mechanics. 2009,76(9):1268-1276.
[14] XIA K W, YAO W. Dynamic rock tests using split Hopkinson (Kolsky) bar system – A review[J]. Journal of Rock Mechanics and Geotechnical Engineering. 2015,7(1):27-59.
[15] 宋义敏, 何爱军, 王泽军, 等. 冲击载荷作用下岩石动态断裂试验研究[J]. 岩土力学. 2015,36(4):965-970.
Song Yiming , He Aijun, Wang Zhe-jun, et al. Experiment study of the dynamic fractures of rock under impact loading[J]. Rock and Soil Mechanics. 2015,36(4):965-970.
[16] 宋义敏, 杨小彬, 金璐, 等. 冲击载荷作用下岩石I型裂纹动态断裂试验研究[J]. 振动与冲击. 2014,33(11):49-53.
SONG Yiming, YANG Xiaobing, JIN Lu, et al. Dynamic fracture test for rock I-type crack under impact load[J]. Journal of Vibration and Shock, 2014, 33(11):49-53.
[17] 潘峰, 党发宁, 焦凯, 等. 冲击荷载作用下不均匀脆性材料动态弯拉强度提高机制研究[J]. 岩石力学与工程学报. 2015(S2):3948-3955.
PAN Feng, DANG Faning, JIAO Kai. et al. Mechanism on enhancement of dynamic flexural tensile strength for nonuniform brittle materials under impact loading[J]. Journal of Rock Mechanics and Engineering. 2015 (S2):3948-3955.
[18] ZHU Z M, LI Y X, XIE J, et al. The effect of principal stress orientation on tunnel stability[J]. Tunnelling and Underground Space Technology. 2015,49:279-286.
[19] 周磊, 朱哲明, 刘邦. 隧道周边不同位置径向裂纹对隧道围岩稳定性影响规律的研究[J]. 岩土工程学报. 2016,38(7):1230-1237.
ZHOU Lei, ZHU Zheming, LIU Bang. Influence of radial cracks on stability of surrounding rocks at different locations around tunnel[J]. Chinese Journal of Geotechnical Engineering. 2016,38(7):1230-1237.
[20] 周磊, 朱哲明, 李元鑫. 基于有限元强度折减法分析主应力方向对隧道稳定性的影响[J]. 现代隧道技术. 2017,54(2):61-67.
ZHOU Lei, ZHU Zheming, LI Yuanxin. Analysis of the influence of principal stress direction on tunnel stability based on finite element strength reduction method[J]. Modern Tunnelling Technology, 2017,54(2):61-67.
[21] FOSTER J T, CHEN W, LUK V K. Dynamic crack initiation toughness of 4340 steel at constant loading rates[J]. Engineering Fracture Mechanics. 2011,78(6):1264-1276.
[22] 李为民, 许金余. 大直径分离式霍普金森压杆试验中的波形整形技术研究[J]. 兵工学报. 2009,30(3):350-355.
Li Weiming,Xu Jinyu. Pulse Shaping Techniques for Large-diameter Split Hopkinson Pressure Bar Test[J]. Acta Arm Amentarii. 2009,30(3):350-355.
[23] ZHU J B, LIAO Z Y, TANG C A. Numerical SHPB Tests of Rocks Under Combined Static and Dynamic Loading Conditions with Application to Dynamic Behavior of Rocks Under In Situ Stresses[J]. Rock Mechanics & Rock Engineering. 2016,49(10):1-12.
[24] CHEN W W, SONG B. Split Hopkinson (Kolsky) Bar-design testing and applications: Springer Science and Business Media; 2010.
[25] ZHOU Y X, XIA K W, LI X B, et al. Suggested Methods for Determining the Dynamic Strength Parameters and Mode-I Fracture Toughness of Rock Materials[J]. International Journal of Rock Mechanics & Mining Sciences. 2011,49(1):105-112.
[26] 郦正能. 应用断裂力学.北京:北京航空航天大学出版. 2012,145-159.
Li Zhengneng. Application of fracture mechanics [M]. Beijing: Beijing University of Aeronautics and Astronautics Press. 2012,145-159.
[27] GAO G, YAO W, XIA K W, et al. Investigation of the rate dependence of fracture propagation in rocks using digital image correlation (DIC) method[J]. Engineering Fracture Mechanics. 2015,138(1):146-155.
[28] 李炼, 杨丽萍, 曹富, 等. 冲击加载下的砂岩动态断裂全过程的实验和分析[J]. 煤炭学报. 2016,41(8).
Li Lian, Yang Liping, Cao Fu, et al. Complete dynamic fracture process of sandstone under impact loading:experiment and analysis[J]. Journal of China Coal Society,2016,41(8):1912-1921.
[29] CHEN Y M. Numerical computation of dynamic stress intensity factors by a Lagrangian finite-difference method (the HEMP code)[J]. Engineering Fracture Mechanics. 1975,7(4):653-660.
[30] 解德, 钱勒, 李长安. 断裂力学中的数值计算方法及工程应用: 科学出版社; 2009. 134-145.
XIE De, QIAN Le, LI Changan. Numerical methods and applications in fracture mechanics[M]. Science Press, 2009:134-145.