组合激励下冷轧机工作辊水平振动特性研究

摘要
图/表
参考文献(26)
相关文章 (15)

全文: PDF (1349 KB) HTML (1 KB)
输出: BibTeX | EndNote (RIS)

摘要为研究冷轧机水平方向在多频激励下发生的组合振动，利用多尺度法求得相应力学模型解析解的近似表达式。在三项激振力频率之和接近系统固有频率时，分析系统非线性振动幅频响应曲线受刚度项和阻尼项系数变化的影响。仿真表明，由于非线性因素影响，使水平系统存在跳跃现象和不稳定区域，当增大系统线性刚度、线性阻尼、非线性阻尼和减小非线性刚度时有利于抑制水平振动；同时发现工作辊水平振动周期会随着激振幅值的变化出现倍周期与混沌周期交替现象，合理选取激振力幅值范围有利于抑制混沌运动的产生；减小轴承座与牌坊立柱间隙能够有效抑制轧机水平振动位移及其碰撞现象。以上研究为抑制轧机水平振动提供了有效理论参考。
关键词：冷轧机；多尺度法；幅频响应曲线；组合振动

	服务

	把本文推荐给朋友
	加入我的书架
	加入引用管理器
	E-mail Alert
	RSS
	作者相关文章
	李丽1
	2
	郝宇超2
	李震2

关键词 ：冷轧机, 多尺度法, 幅频响应曲线, 组合振动

Abstract：Aim to study the combined vibration of the cold rolling mill under multi-frequency excitation in the horizontal direction, an approximate expression of the analytical solution of the corresponding mechanical model is obtained by the multi-scale method. When the sum of the three excitation force frequencies is close to the natural frequency of the system, Analyze the influence of the system's nonlinear vibration amplitude-frequency response curve by the change of stiffness and damping coefficient. Simulation shows that the horizontal system has a jumping phenomenon and unstable regionsdue due to the influence of nonlinear factors. It is beneficial to suppress the horizontal vibration by the linear stiffness, linear damping, nonlinear damping of the system are increased, or the nonlinear stiffness is reduced; at the same time, it is found that the work roll the horizontal vibration period will alternate between the double period and the chaotic period as the excitation amplitude value changes. A reasonable selection of the excitation force amplitude range is beneficial to suppress the generation of chaotic motion; Phenomenas of the rolling mill's horizontal vibration displacement and collision can be effectively suppressed by reducing the gap between the bearing housing and the column. It provides an effective theoretical reference to suppress the rolling mill's horizontal vibration.
Key words:cold rolling mill; multi-scale method; amplitude frequency response curve; combined vibration

Key words： cold rolling mill multi-scale method amplitude frequency response curve combined vibration

收稿日期: 2021-05-06 出版日期: 2022-08-28

引用本文:

李丽1,2，郝宇超2，李震2. 组合激励下冷轧机工作辊水平振动特性研究[J]. 振动与冲击, 2022, 41(16): 135-141.
LI Li1,2，HAO Yuchao2，LI Zhen2. A study on horizontal vibration characteristics of cold rolling mill’s work roll under combined excitation. JOURNAL OF VIBRATION AND SHOCK, 2022, 41(16): 135-141.

链接本文:

http://jvs.sjtu.edu.cn/CN/ 或 http://jvs.sjtu.edu.cn/CN/Y2022/V41/I16/135

[1] 钟掘,唐华平.高速轧机若干振动问题——复杂机电系统耦合动力学研究[J].振动.测试与诊断,2002，22(1):3-10.
ZHONG Jue,TANG Huaping. Vibration Problems of high speed rolling mill——study of dynamics of complex electromechanically coupled system[J]. Journal of VibrationMeasurement ＆ Diagnosis, 2002,22(1):3-10.
[2] 闫晓强.热连轧机机电液耦合振动控制[J].机械工程学报,2011,47(17):61-65.
YAN Xiaoqiang. Machinery-electric-hydraulic coupling vibration control of hot continuous rolling mills[J]. Journal of Mechanical Engineering, 2011,47(17):61-65.
[3] 唐华平,段吉安,钟掘.一个轧机参数振动模型[J].机械科学与技术,2002(5):802-804.
TANG Huaping,DUAN Ji，an,ZHONG Jue. A Model of rolling roller parameter vibration[J]. Mechanical Science and Technology for Aerospace Engineering, 2002(5):802-804.
[4] 曾令强.轧机耦合振动动力学建模及稳定性分析[D].北京：北京科技大学,2017.
[5] 王鑫鑫.基于热连轧机耦合振动的主动抑振控制研究[D].北京：北京科技大学,2019.
[6] 侯福祥,张杰,曹建国,等.带钢冷轧机振动问题的研究进展及评述[J].钢铁研究学报,2007，19(10):6-10.
HOU Fuxiang,ZHANG Jie,CAO Jianguo, et al. Review of chatter studies in cold rolling[J]. Journal of Iron and Steel Research, 2007,19(10):6-10.
[7] ZHENG Y J , SHEN G X , LI Y G , et al. Spatial vibration and its numerical analytical method of four-high rolling mills[J]. Journal of Iron and Steel Research International, 2014(9):837–843.
[8] 毛君,马玉春,谢苗.四辊轧机垂直振动特性研究及测试分析[J].锻压技术,2018,43(4):105-111.
MAO Jun，MA Yuchun，XIE Miao.Research and test analysis on vertical vibration characteristics of four-roller rolling mill[J]. Forging & Stamping Technology,2018,43(4):105-111.
[9] 魏静静,王涛,和东平.波纹辊轧机辊系垂直振动的仿真与分析[J].锻压技术,2020,45(9):143-147.
WEI Jingjing，WANG Tao，HE Dongping.Simulation and analysis on vertical vibration of roll system forcorrugated roll mill[J]. Forging & Stamping Technology, 2020,45(9):143-147.
[10] 和东平,王涛,解加全,等.波纹辊轧机辊系垂直非线性参激振动特性分析[J].振动与冲击,2019,38(20):164-171.
HE Dongping, WANG Tao, XIE Jiaquan et al.An analysis on parametrically excited nonlinear vertical vibration of a roller system in corrugated rolling mills[J]. Journal of Vibration and Shock，2019,38(20):164-171.
[11] 米凯夫,张杰,曹建国,等.基于小波和小波分形的冷连轧机振动识别方法[J].北京科技大学学报,2013,35(8):1064-1071.
MI Kaifu,ZHANG Jie, CAO Jianguo, et al. Vibration identification technology of tandem cold rolling mills based on wavelet and fractal analysis[J]. Journal of University of Science and Technology Beijing, 2013,35(8):1064-1071.
[12] 吴继民,张义方,朱小龙,等.轧机主传动系统在双源扰动作用下的动力学特性研究[J].振动工程学报,2019,32(4):581-589.
WU Jimin, ZHANG Yifang, ZHU Xiaolong et al. Research on dynamic characteristics of main drive system in rolling mill under double source disturbance[J]. Journal of Vibration Engineering, 2019,32(4):581-589.
[13] YAN X Q, QI J B, WANG X X. An active method suppressing rolling mill vibration: disturbance estimation and compensation algorithm[J]. Journal of Iron and Steel Research International,2019,26(7):297-703.
[14] 王鑫鑫,闫晓强.基于扩张状态观测器的轧机振动抑振器研究[J].振动与冲击,2019,38(5):1-6
WANG Xinxin,YAN Xiaoqiang. Vibration suppressor of rolling mills based on extended state observer[J].Journal of Vibration and Shock, 2019,38(5):1-6
[15] 高崇一,杜国君,李蕊,等.考虑轧机主传动系统扭振的带钢非线性振动研究[J].机械强度, 2019, 41(2): 260-266.
GAO Chongyi, DU Guojun, LI Rui, et al. Nonlinear vibration research of strip steel with consideration of torsional vibration of main drive system of rolling mill[J]. Journal of Mechanical Strength,2019, 41(2): 260-266.
[16] 侯东晓,郭大武,陈小辉.基于动态轧制力的四辊轧机垂直–扭转耦合非线性振动特性研究[J].振动与冲击,2020,39(20):106-112.
HOU Dongxiao,GUO Dawu, CHEN Xiaohui. A study on vertical-torsional coupled nonlinear vibration characteristicsof 4- h rolling mill based on dynamic rolling force[J]. Journal of Vibration and Shock, 2020,39(20):106-112.
[17] 王桥医,谭建平.轧制界面非稳态润滑过程系统动力学模型的建立及其数值模拟[J].中国机械工程,2005(9):831-834.
WANG Qiaoyi, TAN Jianping .System dynamics research and numerical simulation onunsteady lubrication based on the interface of rolling[J]. China Mechanical Engineering, 2005(9):831-834.
[18] 王桥医,崔明超,王瀚,等.基于辊系多模态模式的连轧机机架间耦合振动系统模型的建立及仿真分析[J].中南大学学报（自然科学版）,2020,51(10):2834-2843.
WANG Qiaoyi,CUI Mingchao,WANG Han, et al. Establishment and simulation analysis of coupled vibration system model between stands of tandem rolling mills based on rollers multi-modal mode.[J]. Journal of Central South University (Science and Technology), 2020,51(10):2834-2843.
[19] LU X , SUN J , LI G , et al. Stability analysis of a nonlinear coupled vibration model in a tandem cold rolling mill[J]. Shock and Vibration, 2019, 2019(2):1-14.
[20] 张阳,孙建亮,杜东源.板带轧机柔性多体系统耦合动力学建模研究[J].机械强度,2019,41(4):799-806.
ZHANG Yang, SUN Jianliang, DU Dongyuan.Strip rolling mill’s flexible multi-body system coupling dynamic modeling research[J]. Journal of Mechanical Strength. 2019,41(4):799-806.
[21] 周家林,吴凡,张月领,等.单辊驱动冷轧平整机的水平振动研究[J].武汉科技大学学报,2019,42(3):174-181.
ZHOU Jialin, WU Fan,ZHANG Yueling, et al.Horizontal vibration of a single-roll driven cold rolling temper mill[J]. Journal of Wuhan University of Science and Technology, 2019,42(3):174-181.
[22] 闫晓强,赵少华,孙复森,等.四辊中板轧机钢板波浪生成与抑制之五──工作辊附加水平力的确定[J].工程科学学报,1999(3):288-291.
YAN Xiaoqiang, ZHAO Shaohua, SUN Fusen, et al.Forming and curbing of jobbing sheet waviness on four high jobbing sheet mill(5)-setting up the model of additional horizontal forcr[J]. Chinese Journal of Engineering, 1999(3):288-291.
[23] 王桥医,朱媛,过山,等.高速冷轧机辊系非线性动力学模型及控制参数优化[J].中国机械工程,2019,30(8):896-901.
WANG Qiaoyi, ZHU Yuan, GUO Shan ,et al.Nonlinear dynamics model and control parameter optimization of roll system on high-speed cold rolling mills[J]. China Mechanical Engineering, 2019,30(8):896-901.
[24] 凌启辉,赵前程,王宪,等.热连轧机工作辊水平-垂直非线性振动特性及抑制[J].中国机械工程,2017,28(16):1943-1950.
LING Qihui,ZHAO Qiancheng,WANG Xian, et al.Work roll horizontal-vertical nonlinear vibration characteristics and suppression of hot strip tandem mills[J]. China Mechanical Engineering, 2017,28(16):1943-1950.
[25] 孟宗,付立元,宋明厚.一类非线性相对转动系统的组合谐波分岔行为研究[J].物理学报,2013,62(5):244-253.
MENG Zong,FU Liyuan,SONG Minghou. Bifurcation of a kind of nonlinear-relative rotational system with combined harmonic excitation[J]. Acta Physica Sinica, 2013,62(5):244-253.
[26] 孙韵韵,肖会芳,徐金梧.考虑轧制界面粗糙形貌的轧机辊系非线性振动特性研究[J].振动与冲击,2017,36(8):113-120.
SUN Yunyun,XIAO Huifang,XU Jinwu. Nonlinear vibration characteristics of a rolling mill systemconsidering the roughness of rolling interface[J]. Journal of Vibration and Shock, 2017,36(8):113-120.