Abstract：Fused deposition modelling (FDM) is a fast growing rapid prototyping technology.It is able to build functional parts with complex geometrical shapes in reasonable time.However, the mechanical property of the built parts is hardly comparable to those produced by the traditional method, which is one of the most obvious defects that hinder the development of rapid prototyping technology.For the first time, this paper utilized vibration into the FDM process to improve the dynamic property of FDM parts.Firstly, a vibrating FDM 3D printer was set up to introduce vibration into the FDM process.The samples built in the Z and the X directions without and with vibration applied were then manufactured respectively, followed by the corresponding impact hammer tests performed.Finally, the effect of applied vibration on the dynamic property of FDM plates was experimentally investigated.It is shown that the applied vibration can significantly change the natural frequency, decrease the resonant response, and increase the modal damping ratio, thus improve the anti-vibration capability of FDM plates.
收稿日期: 2018-03-27
出版日期: 2019-08-15
引用本文:
姜世杰，Yannick Siyajeu，史银芳，孙宁宁，赵春雨. 振动利用对FDM薄板动力学性能的影响研究[J]. 振动与冲击, 2019, 38(16): 1-6.
JIANG Shijie,Yannick Siyajeu,SHI Yinfang,SUN Ningning,ZHAO Chunyu. Experimental investigation on the effect of utilizing vibration on the dynamic property of FDM plates. JOURNAL OF VIBRATION AND SHOCK, 2019, 38(16): 1-6.
[1] S. K. Panda, S. Padhee, S. Anoop Kumar, and S. Mahapatra. Optimization of fused deposition modelling (FDM) process parameters using bacterial foraging technique [J]. Intelligent information management, vol. 1, p. 89, 2009.
[2] A. Arivazhagan and S. H. Masood. Dynamic mechanical properties of ABS material processed by fused deposition modelling [J]. International Journal of Engineering Research and Applications, vol. 2, pp. 2013-2014, 2012.
[3] H. Bikas, P. Stavropoulos, and G. Chryssolouris. Additive manufacturing methods and modelling approaches: a critical review [J]. International Journal of Advanced Manufacturing Technology, vol. 83, pp. 389-405, 2016.
[4] I. Brensons, S. Polukoshko, A. Silins, and N. Mozga. FDM prototype experimental research of processing parameter optimization to achieve higher tensile stress [J]. Solid State Phenomena, 2014.
[5] O. A. Mohamed, S. H. Masood, and J. L. Bhowmik. Experimental investigations of process parameters influence on rheological behavior and dynamic mechanical properties of FDM manufactured parts [J]. Materials and Manufacturing Processes, vol. 31, pp. 1983-1994, 2016.
[6] J. Torres, J. Cotelo, J. Karl, and A. P. Gordon. Mechanical property optimization of FDM PLA in shear with multiple objectives [J]. Jom, vol. 67, pp. 1183-1193, 2015.
[7] F. Rayegani and G. C. Onwubolu. Fused deposition modelling (FDM) process parameter prediction and optimization using group method for data handling (GMDH) and differential evolution (DE) [J]. The International Journal of Advanced Manufacturing Technology, vol. 73, pp. 509-519, 2014.
[8] I. Durgun and R. Ertan. Experimental investigation of FDM process for improvement of mechanical properties and production cost [J]. Rapid Prototyping Journal, vol. 20, pp. 228-235, 2014.
[9] O. Lužanin, D. Movrin, and M. Plančak. Effect of layer thickness, deposition angle, and infill on maximum flexural force in FDM-built specimens [J]. Journal for Technology of Plasticity, vol. 39, pp. 49-58, 2014.
[10] S. H. Masood, K. Mau, and W. Song. Tensile properties of processed FDM polycarbonate material [J]. in Materials Science Forum, 2010, pp. 2556-2559.
[11] B. N. Panda, M. R. Bahubalendruni, and B. B. Biswal. A general regression neural network approach for the evaluation of compressive strength of FDM prototypes [J]. Neural Computing and Applications, vol. 26, pp. 1129-1136, 2015.
[12] A. K. Sood, R. K. Ohdar, and S. S. Mahapatra. Experimental investigation and empirical modelling of FDM process for compressive strength improvement [J]. Journal of Advanced Research, vol. 3, pp. 81-90, 2012.
[13] O. A. Mohamed, S. H. Masood, J. L. Bhowmik, M. Nikzad, and J. Azadmanjiri. Effect of process parameters on dynamic mechanical performance of FDM PC/ABS printed parts through design of experiment [J]. Journal of Materials Engineering and Performance, vol. 25, pp. 2922-2935, 2016.
[14] O. A. Mohamed, S. H. Masood, and J. L. Bhowmik. Investigation of dynamic elastic deformation of parts processed by fused deposition modeling additive manufacturing [J]. Advances in Production Engineering & Management, vol. 11, pp. 227-38, 2016.
[15] E. Foroozmehr, D. Lin, and R. Kovacevic. Application of vibration in the laser powder deposition process [J]. Journal of Manufacturing Processes, vol. 11, pp. 38-44, 2009.
[16] 孙伟, 齐飞, 韩清凯. 基于自由振动衰减信号包络线法辨识硬涂层复合结构的阻尼特性[J]. 振动与冲击, vol. 32, pp. 50-54, 2013.
SUN Wei, QI Fei, HAN Qing-kai. Estimating system damping for a hard coating composite structure based on envelope of a free damped vibration signal [J]. Journal of Vibration and Shock, vol. 32, pp. 50-54, 2013.
[17] 郭建英, 白艳艳. 剪切变形与转动惯量对层合金属厚壁短管振动模态的影响[J]. 振动与冲击, Vol. 36, No. 21, pp. 107-116, 2017.
GUO Jian-ying, BAI Yan-yan. Effects of shear deformation and rotary inertia on the vibration of laminated thick-walled short tubes [J]. Journal of Vibration and Shock, Vol. 36, No. 21, pp. 107-116, 2017.
[18] N. K. Mandal, R. A. Rahman, and M. S. Leong. Experimental study on loss factor for corrugated plates by bandwidth method [J]. Ocean Engineering, vol. 31, pp. 1313-1323, 2004.
[19] K.-L. Wong, J.-S. Row, C.-W. Kuo, and K.-C. Huang. Resonance of a rectangular microstrip patch on a uniaxial substrate [J]. IEEE Transactions on Microwave Theory and techniques, vol. 41, pp. 698-701, 1993.
