力负载对超声切割声学系统谐振频率及谐振阻抗的影响

摘要
图/表
参考文献(15)
相关文章 (7)

全文: PDF (961 KB) HTML (1 KB)
输出: BibTeX | EndNote (RIS)

摘要针对在蜂窝复合材料超声波切割加工中，超声切割系统在受力之后会出现系统失谐，振幅不足甚至停振的现象，对声学系统受力之后的阻抗值以及谐振频率进行研究。利用四端网络法，通过分析变幅杆、压电陶瓷以及端盖等组成声学系统各部分输入输出特性，提出了声学系统的整体设计方程，得出了声学系统的阻抗值和频率方程以及负载﹑电流与振幅的关系式，并对超声切割系统的受力模型进行分析。通过对超声切割声学系统施加单向力，分析受力之后的声学系统阻抗值和谐振频率，得出声学系统受力对系统阻抗值和谐振频率的影响规律。实验结果表明：增加三个方向力之后，系统的阻抗值和谐振频率都会上升。随着力负载的增加，Y、Z方向施加力负载时的系统阻抗值比X方向施加力负载时增加得更快，而在系统谐振频率方面，X、Z方向施加力负载时谐振频率的增量比Y方向施加力负载时更大，在实际应用中应减小敏感方向的力。本文的研究结果可以为实际加工提供理论指导。

	服务

	把本文推荐给朋友
	加入我的书架
	加入引用管理器
	E-mail Alert
	RSS
	作者相关文章

关键词 ：超声切割系统, 力负载, 受力模型, 阻抗值, 谐振频率

Abstract：The ultrasonic cutting system will be out of harmony, insufficient harmony, or non-resonance when the force is loaded on, it has serious impact on the machining process and the machining quality of the workpiece. In this paper, the impedance and the resonance frequency of the force loaded acoustic system were studied. By using terminal network method, Input / output characteristics of ultrasonic horn, piezoelectric ceramics and end cover were studied, the integral design equation of the acoustic system was presented, and the impedance, frequency equation and the relationship among load, current and amplitude of the acoustic system were obtained. In order to get influence law of force on impedance and resonant frequency, a digital push pull meter was applied to load a single direction force to the acoustic system, the relationship among the impedance, resonant frequency and force was tested by experiments. Experimental results show that the impedance of the system is increased after three directions are loaded on. With the increase in loaded force, the impedance of ultrasonic cutting system loaded Y and Z direction force increases faster than that of the X direction, the increase in resonant frequency of ultrasonic cutting system loaded X and Z direction force is much more than that of Y direction, we should reduce the force of the sensitive direction in practical application. The research results of this paper can provide theoretical guidance for the actual processing.

Key words： ultrasonic cutting system loaded force load model impedance resonance frequency

收稿日期: 2015-10-15 出版日期: 2016-11-25

引用本文:

纪华伟，虞文泽，胡小平. 力负载对超声切割声学系统谐振频率及谐振阻抗的影响[J]. 振动与冲击, 2016, 35(23): 136-141.
Ji Huawei Yu Wenze Hu Xiaoping. Influence of the Force Load on the Resonance Frequency and Resonance Impedance of the Ultrasonic Cutting Acoustic System. JOURNAL OF VIBRATION AND SHOCK, 2016, 35(23): 136-141.

链接本文:

http://jvs.sjtu.edu.cn/CN/ 或 http://jvs.sjtu.edu.cn/CN/Y2016/V35/I23/136

[1] 高军，崔巍. 超声切割技术在复合材料加工领域的应用[J]. 航空制造技术,2008,(04):50-52.
   Gao Jun，Cui wei. Ultrasonic cutting technology applying in the field of composite material processing [J]. Aeronautial Manufacturing Technology,2008,(04):50-52.
[2] 贺西平，高杰. 超声变幅杆设计方法研究[J]. 声学技术, 2006.25(01):82-86.
   He Xiping, Gao Jie. A review of ultrasonic solid horn design[J]. Technical acoustics, 2006,25(01):82-86.
[3] 黄德中. 超声波振动器四端网络设计[J]. 振动与冲击, 2005,24(05): 110-111.
   Huang Dezhong. Design of ultrasonic vibrator using four-end network method[J]. Journal of Vibration And Shock.2005,24(05):110-111.
[4] 曾凡冲. 超声换能器的设计理论研究[D]. 北方工业大学, 2013.
   Zeng Fanchong. The study on the design theory of ultrasonic thansducer[D]. North China University of Technology, 2013.
[5] 赵福令，冯冬菊，郭东明等. 超声变幅杆的四端网络法设计[J]. 声学学报, 2002,27(06): 554-558.
   Zhao Fuling, Feng Dongju. Design of horn using four-endnetwork method[J]. Acta Acustica. 2002,27(06):554-558.
[6] Kei Harada, Hiroyuki. Effect of dynamic response and displacement/stress amplitude on oltrasonic vibration cutting[J]. Journal of materials processing technology, 2009,209:4490-4495.
[7] Li Zhang, Jingyan Dong, Paul H.Cohen. Material-insensitive feature depth control and machining force reductionby ultrasonic vibration in AFM-Based nanomachining[J]. IEEE transactions on nanotechnology, 2013,12(5):743-750.
[8] Efim Sh.Statnikov, Oleg V.Korolkov, Vladimir N.Vityazev. Physics and mechanism of ultrasonic impact[J]. Ultrasonics, 2006,44:533-538.
[9] X.J,Zhu, J.Q.Wang, Q.Cheng, Z.M.Lu. Research on dynamic grinding force in ultrasonic honing chatter[J]. Key Engineering Material,2011,487:433-437.
[10] 张云电，喻家英，王纯. 珩磨负载对超声珩磨振动系统谐振频率的影响[J].声学学报,1994,14(05):367-371.
   Zhang Yundian, Yu Jiaying, Wang Chun. Influence of honing load on resonance frequency of ultrasonic honing vibration system[J]. Acta Acustica,1994,14(05):367-371.
[11] 李华，任坤，殷振，等.纵弯转换球面超声振动聚焦系统谐振特性研究[J].振动与冲击,2015,34(6):183-188.
LI Hua, REN Kun, YIN Zhen,et al.Resonance features of a new ultrasonic vibration focusing system based on longitudinal-flexural vibration conversion[J].Journal of Vibration and Shock,2015,34(6):183-188.
[12] 赵波，刘折，靳宇晖. 负载对超声加工声学系统特性的影响[J]. 航空精密制造技术. 2012,48(01): 10-13.
Zhao bo, Liu Zhe,Jin Yuhui. Study on influence of load on acoustic system characteristics of ultrasonic machining[J]. Aviation Precision Manufacturing Technology. 2012,48(01):10-13.
[13]尹晓春，谢欣平，田阿利. 考虑负载影响的阶梯形超声变幅杆动力特性[J]. 振动与冲击. 2012,31(04): 157-161.
   Yi Xiaochun, Xie Xinping, Tian Eli. Dynamical performance of ultrasonic stepped horn with consideration of lo ding effect[J]. Journal of Vibration And Shock. 2012,31(04):157-161.
[14]于伟，阎长罡，李伟. 抗性负载的余弦形复合变幅杆设计及动力学特性研究[J]. 机床与液压. 2011,39(13): 13-16.
   Yu Wei, Yan Changgang, Li Wei. Design and dynamical analysis on a cylindrical and cosine composite horn with reactive load[J]. Machine Tool &Hydraulics. 2011,39(13):13-16.
[15]林书玉，姚文苇.阻性负载超声变幅杆振动特性研究[J]. 声学技术. 2006,25(05): 494-498.
   Lin Shuyu, Yao Wenwei. Characteristics of ultrasonic horn with resistance load[J]. Technical Acoustics.2006, 25(05):494-498.