1，State Key Laboratory of Coal Mine Disaster Dynamics and Control，Chongqing 400030，
2，National & Local Joint Engineering Laboratory of Gas Drainage in Complex Coal Seam，Chongqing 400030
In order to solve the problem of measurement of velocity of abrasive in abrasive water jet，based on PIV technology，combined with image processing and filtering analysis technology，this paper presents a non-contact measurement method ,which is a method for measuring the velocity of abrasive in abrasive water jet. The velocity and location information of abrasive in the abrasive water jet can be obtained simultaneously by this method. By using this approach, an abrasive velocity test experiment was carried out, the experimental results show that: (1) This method can get the velocity of abrasive in abrasive water jet quickly; (2) The variation of velocity of abrasive along the jet direction at the nozzle exit has been obtained. The velocity of abrasive at the nozzle exit increases first and then decreases and the maximum speed exists, which means there is an optimal target distance in abrasive water jet. (3) The variation of velocity of abrasive along the jet radial direction at the nozzle exit has been obtained by using this method. The largest velocity of abrasive is in the center of the abrasive jet. And the velocity gradually decreases from the center to the boundary，shows a bell-shaped velocity profile.
章文峰1，2，卢义玉1，2，汤积仁1，2，黄 飞1，2. 基于PIV技术的磨料水射流中固体磨料粒子速度分布实验研究[J]. 振动与冲击, 2016, 35(8): 159-165.
ZHANG Wen-feng1，2，LU Yi-yu1，2，TANG Ji-ren1，2，HUANG Fei1，2，LI Liang-wei1，2 . Experimental study of velocity distribution of solid abrasive particle in abrasive water jet based on PIV technology. JOURNAL OF VIBRATION AND SHOCK, 2016, 35(8): 159-165.
[1] 林晓东，卢义玉，汤积仁，等.基于SPH-FEM耦合算法的磨料水射流破岩数值模拟[J]. 振动与冲击,2014,18:170-176.
LIN Xiao-dong,LU Yi-yu,TANG Ji-ren,et al.Numerical simulation of abrasive water jet breaking rock with SPH-FEM coupling algorithm[J].JOURNAL OF VIBRATION AND SHOCK, 2014,18:170-176.
[2] 于鸿春. 磨料射流油井割缝技术与理论的研究[D].中国石油大学,2007.
Yu Hong-chun. Oil Well Abrasive Jet Slotting Technology and Its Theoretical Research [D]. China University of Petroleum (East China), 2007.
[3] 林柏泉，吕有厂，李宝玉，等.高压磨料射流割缝技术及其在防突工程中的应用[J].煤炭学报,2007,09: 959-963.
LIN Bai-quan, LU You-chang, LI Bao-yu,et al. High pressure abrasive hydraulic cutting seam technology and its application in outbursts prevention [J]. JOURNAL OF CH INA COAL SOCIETY, 2007, 09:959-963.
[4] 李兆泽. 磨料水射流抛光技术研究[D].国防科学技术大学,2011.
Li Zhao-ze. Study on Abrasive Jet Polishing Technology [D]. National University of Defense Technology, 2011.
[5] R. Balz ，R. Mokso， C. Narayanan．Ultra-fast X-ray particle velocimetry measurements within an abrasive water jet [J] ．Exp Fluids (2013) 54:1476 ．
[6] 王明波. 磨料水射流结构特性与破岩机理研究[D].中国石油大学,2007.
Wang, Ming-bo．Abrasive Water Jet Flow Property and Rock-breaking Mechanism[D].China University of Petroleum，2007 ．
[7] Swanson R.K., KILMAN M., CERWIN S., HOUSSAYE G. Study of particle Velocities in Water Driven Abrasive Jet Cutting [J]. Proceedings of the 4th American Water Jet Conference, ASME, 1987:103-108.
[8] MILLER.A.L, ARCHIBALD.J.H. Measurement of particle velocities in an abrasive jet cutting system [J].6th American Water Jet Conference, 1991:291-304.
[9] CHEN W.L., GESKIN E.S. Measurements of the velocity of abrasive water jet by the use of laser transit anemometer [J].Jet Cutting Technology-Proceedings of the 10th International Conference, 1990:23-26.
[10] CHEN W.L., GESKIN E.S. Correlation between particle velocity and conditions of abrasive water jet formation [A]. Proceedings of the 6th American Water Jet Conference, 1991:305-313.
[11] K.F.Neusen, T.J.Gores, T.J.Labus. Measurement of particle and drop velocities in a mixed abrasive water jet using a forward-scatter LDV system [A].Dordrecht: Kluwer Academic Publishing, 1992:63-74.
[12] A.N.J Stevenson, I.M. Hutchings. Scaling laws for particle velocity in the gas-blast erosion test [J].Wear, 1995:56-62.
[13] H.-T. Liu, P.J. Miles, N. Cooksey. Measurements of water-droplet and abrasive speeds in an ultrahigh-pressure abrasive-water jet [A].Houston, Texas, 1999.
[14] 刘祖军，贾明晓，杨詠昕. 闭口单箱颤振的流场机理[J]. 振动与冲击,2012,12:22-27.
Yu Hong-chun. Oil Well Abrasive Jet Slotting Technology and Its Theoretical Research [D]. China University of Petroleum (East China), 2007.
[15] 孙宏琦，施维颖，巨永锋．利用中值滤波进行图像处理[J]. 长安大学学报(自然科学版) ，2003，02：104-106.
SUN Hong-qi,SHI Wei-ying,JU Yong-feng.Image processing with medium value filter[J].Journal of Chang’an University( Natural Science Edition)，2003，02：104-106.
[16] 赵荣珍，李超，张优云. 中值与小波消噪集成的转子振动信号滤波方法研究[J]. 振动与冲击,2005,04:74-77+140-141.
Zhao Rong-zhen,Li Chao, Zhang You-yun. Filter design synthesizing median filtering and wavelet algorithm to de-noise vibration signal polluted by violent pulse noises [J]. JOURNAL OF VIBRATION AND SHOCK, 2005, 04:74-77+140-141.
[17] 冯新星，张丽艳，叶南，等. 二维高斯分布光斑中心快速提取算法研究[J]. 光学学报,2012,05:78-85.
Feng Xin-xing,Zhang Li-yan,Ye Nan,et al. Fast Algorithms on Center Location of Two Dimensional Gaussian Distribution Spot [J] ．Acta Optica Sinica，2012，05：78-85．
[18] H.Z.Li, J.Wang, J.M.Fan. Analysis and modelling of particle velocities in micro-abrasive air jet [J].International Journal of Machine Tools &Manufacture，2009 (49) ：850–858.
[19] 康勇，王晓川，卢义玉，等. 磨料射流辅助三翼钻头破岩实验研究[J]. 中国矿业大学学报,2012,02:212-218.
KANG Yong,WANG Xiao-chuan,LU Yi-yu,et al.Experimental study of rock breaking by a three wing abrasive jet assisted drill cut[J] ．Journal of China University of Mining & Technology，2012，02：212-218．
[20] L. Boguslawsk,C.O. Popiel. Flow structure of the free round turbulent jet in the initial region[J] ． Journal of Fluid Mechanics , 1979，90：531–539．
[21] 沈忠厚．水射流理论与技术[M]．东营: 石油大学出版社, 1998. 293- 327.
[22] 李晓红，卢义玉，向文英．水射流理论及在矿业工程中的应用[M]．重庆: 重庆大学出版社, 2007.118-152.
[23] J.M. Fan, H.Z. Li，J. Wang,et al. A study of the flow characteristics in micro-abrasive jets [J] ．Experimental Thermal and Fluid Science ，2011，35： 1097–1106．
[24] 左伟芹. 前混合磨料射流磨料加速机理及分布规律[D].重庆大学,2012.
Zuo Wei-qin. Abrasive Accelerated Mechanisms and Distribution Law in Pre-mixed Abrasive Jet[D] ．Chongqing University，2012．
[25] 王明波，王瑞和. 喷嘴内液固两相射流流场的数值模拟[J]. 石油大学学报(自然科学版) ,2005,05: 46-49.
WANG Ming-bo,WANG Rui-h.Numerical simulation on fluid-particle two-phase jet flow field in nozzle[J] ．Journal of the University of Petroleum , China，2005，05：46-49．
[26] 李宝玉，郭楚文，林柏泉. 用于安全切割的磨料水射流喷嘴设计理论和方法[J]. 煤炭学报,2005,02:251-254.
LI Bao-yu,GUO Chu-wen,LIN Bai-quan．Theory and method of designing abrasive water-jet nozzle in safety cutting[J] ．JOURNAL OF CH INA COAL SOC IETY，2005，02：251-254．
[27] 陆国胜，龚烈航，王强，等. 前混合磨料水射流磨料颗粒加速机理分析[J]. 解放军理工大学学报(自然科学版),2006,03:275-280.
LU Guo-sheng,GONG Lie-hang,WANG Qiang,et al. Research on acceleration mechanism of abrasive in pre-mixed abrasive water-jet[J] ．Journal of PLA University of Science and Technology，2006，03：275-280．
