酒杯型输电铁塔曲臂风荷载风洞试验研究

杨风利1,牛华伟2,杨靖波1,张宏杰1

振动与冲击 ›› 2017, Vol. 36 ›› Issue (24) : 170-176.

PDF(1887 KB)
PDF(1887 KB)
振动与冲击 ›› 2017, Vol. 36 ›› Issue (24) : 170-176.
论文

酒杯型输电铁塔曲臂风荷载风洞试验研究

  • 杨风利1,牛华伟2,杨靖波1,张宏杰1
作者信息 +

Wind tunnel tests for wind loads of crank arms of cup-type transmission towers

  • YANG Fengli1, NIU Huawei2, YANG Jingbo1, ZHANG Hongjie1
Author information +
文章历史 +

摘要

酒杯塔是1000kV特高压输电线路工程中的常用塔型,设计时曲臂风荷载计算存在使用模型不统一的问题,而目前还没有针对曲臂风荷载的专门研究。完成了15m/s和20m/s来流风速下酒杯型输电铁塔曲臂模型的风洞试验,得到了11种风向角下的风轴和体轴平均阻力系数,获得了曲臂模型迎风面、背风面体型系数和背风面风荷载降低系数η,分析了酒杯型输电铁塔曲臂角度风荷载系数和有效投影面积,将试验确定的曲臂风荷载计算参数与国内外规范值进行了对比分析,提出了酒杯型输电铁塔曲臂角度风荷载的设计建议。按中国规范“塔身”模型计算曲臂风荷载满足安全要求,风向角为90°时曲臂风整体风荷载取值偏于保守;风向角为45°、60°和90°时,按中国规范“横担”模型计算的曲臂风荷载远低于风洞试验值,将低估曲臂风荷载并使结构抗风设计存在安全隐患。

Abstract

Cup-type transmission towers are frequently used in 1000kV UHV transmission lines. However, different calculation models are used for wind loads calculation of crank arms in design. Until now there has been no specialized study on wind loads of cranks arms. Wind tunnel tests were conducted on crank arm models of a cup-type transmission tower under 15m/s and 20m/s wind velocities. The drag coefficients along wind direction axis and body-fitted axis for 11 skewed angles were obtained. The models’ shape coefficients over the windward surface and the leeward one, respectively and the leeward surface shielding factor η of the models were obtained. The skewed wind load factors and the effective projected areas (EPA) of the models were analyzed. The parameters determined with the wind tunnel tests for the wind loads calculation of crank arms were compared with standard values in Chinese and foreign codes. Some design suggestions for the wind loads calculation of crank arms of cup-type transmission towers were proposed. It was shown that the wind loads of crank arms calculated according to the tower body model of Chinese code can meet safety requirements, but the total wind loads of crank arms calculated for 90° wind incidence angle are conservative; the wind loads of crank arms calculated according to the cross-arm model of Chinese code are much lower than the wind tunnel test values for 45°, 60° and 90° wind incidence angles, so the wind loads of crank arms are underestimated and there is a safety hazard in anti-wind design of structures.
 
 

关键词

输电铁塔 / 曲臂 / 遮挡效应 / 角度风 / 风洞试验

Key words

 transmission tower / crank arm / shielding effect / skewed wind / wind tunnel test

引用本文

导出引用
杨风利1,牛华伟2,杨靖波1,张宏杰1. 酒杯型输电铁塔曲臂风荷载风洞试验研究[J]. 振动与冲击, 2017, 36(24): 170-176
YANG Fengli1, NIU Huawei2, YANG Jingbo1, ZHANG Hongjie1. Wind tunnel tests for wind loads of crank arms of cup-type transmission towers[J]. Journal of Vibration and Shock, 2017, 36(24): 170-176

参考文献

[1] DL/T 5154-2012,架空输电线路杆塔结构设计技术规定[S].北京:中国计划出版社,2012.
DL/T 5154-2012,Technical code for the design of tower and pole structures of overhead transmission lines[S].Beijing:China Planning Press,2012.(in Chinese)
[2] American Society of Civil Engineers.ASCE manuals and reports on engineering practice No.74[S].Reston:American Society of Civil Engineers,1991.
[3] American Society of Civil Engineers.ASCE manuals and reports on engineering practice No.74[S].Reston:American Society of Civil Engineers,2010.
[4] International Electrotechnical Commission.IEC 60826,Design criteria of overhead transmission lines [S].Geneva:International Electrotechnical Commission,2003.
[5] Japanese Electrotechnical Committee.JEC-127-1979,Design standards on structures for transmissions[S]. Tokyo,JEC,1979.
[6] British Standards Institution.BS-8100:1986,Lattice tower and masts-Part1:Code of practice for loading [S].London:British Standards Institution,2005.
[7] 吕付玉,刘宏滨.道亨铁塔满应力分析软件与自立式铁塔内力分析软件的对比分析[J]. 广东电力,2011,24(6):31-34.
Lyu Fuyu,Liu Hongbin.Comparative Analysis of Daoheng MYL Software and TTA Software[J].Guangdong Electric Power,2011,24(6):31-34.(in Chinese)
[8] Bayar,D.C..Drag coefficients of latticed towers [J]. Journal of Structural Engineering,1986,112:417-430.
[9] 邹良浩,梁枢果,邹垚,等.格构式塔架风载体型系数的风洞试验研究[J]. 特种结构,2008,25(5):41-43.
Zou Lianghao,Liang Shuguo,Zou Yao,et al.Wind tunnel test on wind load shape coefficients of lattice towers[J].Special Structures,2008,25(5): 41-43.(in Chinese)
[10] 张庆华,顾明,黄鹏.典型输电塔塔头风力特性试验研究[J]. 振动工程学报,2008,21(5):452-457.
Zhang Qinghua,Gu Ming,Huang Peng.Experiment on wind force on typical superstructures of latticed transmission tower[J].Journal of Vibration Engineering,2008,21(5):452-457.(in Chinese)
[11] 邓洪洲,张建明,帅群,等.输电钢管塔体型系数风洞试验研究[J]. 电网技术,2010,34(9):190-194.
Deng Hongzhou,Zhang Jianming,Shuai Qun,et al.Wind-tunnel investigation on pressure coefficient of steel tubular transmission tower[J].Power System Technology,2010,34(9):190-194.(in Chinese)
[12] T.G. Mara,T.C.E. Ho.Design loads for transmission towers under skewed wind loading[C]. Structures Congress 2011,Las Vegas,American Society of Civil Engineers (ASCE),2001:1246-1257.
[13] Fengli Yang,JingboYang,Huawei Niu,et al.Design wind loads for tubular-angle steel cross-arms of transmission towers under skewed wind loading. Journal of Wind Engineering and Industrial Aerodynamics,2015,140,10-18.

PDF(1887 KB)

Accesses

Citation

Detail

段落导航
相关文章

/