自由磨料射流轴心磨料速度模型及分析

PDF(1258 KB)

振动与冲击 ›› 2018, Vol. 37 ›› Issue (10) : 157-163.

论文

自由磨料射流轴心磨料速度模型及分析

章文峰1,2，卢义玉1,2，汤积仁1,2，陆晓辉1,2,程玉刚1,2

作者信息 +

Analysis and modeling on the particle velocities along the centerline of a free abrasive water jet

ZHANG Wenfeng1,2，LU Yiyu1,2，TANG Jiren1,2，LU Xiaohui1,2，CHENG Yugang1,2

Author information +

文章历史 +

摘要

为了研究自由磨料射流轴心磨料速度，以自由磨料射流轴心磨料为研究对象，利用自由磨料射流轴心流体速度方程及磨料运动方程，建立了自由磨料射流轴心磨料速度模型，并基于等分法和迭代算法的数值求解方法，求解了该速度模型，得出了自由磨料射流轴心磨料速度变化规律，最后利用PIV实验对该速度模型进行了验证。结果表明：(1) 自由磨料射流轴心磨料速度随着磨料运动距离的增加先增大后减小；在初始段末端磨料速度未达到速度最大值，磨料速度最大值出现在基本段内。(2) 自由磨料射流轴心磨料速度PIV实测值与理论值的变化趋势基本一致；实测值与理论值的平均百分比误差和标准偏差分别小于3%和2m/s，吻合较好，验证了模型的正确性和准确性。

Abstract

In order to study the velocities of the particles along the centerline of a free abrasive water jet, a model for the particle velocities was established based on the fluid velocity equation and particle motion equation. The model was solved numerically by using the bisection method and iterative algorithm and the distribution of particle velocity along the centerline of free abrasive water jet was obtained. The results of the model were then verified by PIV experiments. The results show that: with the increase of the moving distance, the particle velocity increases first and then decreases, at the end of the initial section, the particle velocity does not reach its maximum and the maximum of the particle velocity appears in the basic section. The changing trend of the measured value of PIV experiments is consistent with the theoretical value. The results of the model calculations and the corresponding referential experiments are in good agreement with less than 2% average errors and 2 m/s the standard deviation, which verifies the correctness and accuracy of the model.

导出引用

章文峰1,2，卢义玉1,2，汤积仁1,2，陆晓辉1,2,程玉刚1,2. 自由磨料射流轴心磨料速度模型及分析[J]. 振动与冲击, 2018, 37(10): 157-163

ZHANG Wenfeng1,2，LU Yiyu1,2，TANG Jiren1,2，LU Xiaohui1,2，CHENG Yugang1,2. Analysis and modeling on the particle velocities along the centerline of a free abrasive water jet[J]. Journal of Vibration and Shock, 2018, 37(10): 157-163

参考文献

[1]林晓东，卢义玉，汤积仁，等.基于SPH-FEM耦合算法的磨料水射流破岩数值模拟[J]. 振动与冲击,2014,18:170-176.
LIN Xiao-dong,LU Yi-yu,TANG Ji-ren,et al.Numerical simulation of abrasive water jet breaking rock with SPH-FEM coupling algorithm[J].JOURNAL OF VIBRATION AND SHOCK, 2014,18:170-176.
[2]R. Balz ，R. Mokso， C. Narayanan．Ultra-fast X-ray particle velocimetry measurements within an abrasive water jet [J] ．Exp Fluids (2013) 54:1476.
[3]于鸿春. 磨料射流油井割缝技术与理论的研究[D].中国石油大学,2007.
Yu Hong-chun. Oil Well Abrasive Jet Slotting Technology and Its Theoretical Research [D]. China University of Petroleum (East China), 2007.
[4]林柏泉，吕有厂，李宝玉，等.高压磨料射流割缝技术及其在防突工程中的应用[J].煤炭学报,2007,09: 959-963.
LIN Bai-quan, LU You-chang, LI Bao-yu,et al. High pressure abrasive hydraulic cutting seam technology and its application in outbursts prevention [J]. JOURNAL OF CH INA COAL SOCIETY, 2007, 09:959-963.
[5]李兆泽. 磨料水射流抛光技术研究[D].国防科学技术大学,2011.
Li Zhao-ze. Study on Abrasive Jet Polishing Technology [D]. National University of Defense Technology, 2011.
[6]Lu Yiyu, Tang Jiren, Ge Zhaolong, et al et al. Hard rock drilling technique with abrasive water jet assistance[J]. International Journal of Rock Mechanics & Mining Sciences, 2013, 60(2):47-56.
[7] Kim, Jung Gyu, and J. J. Song. Abrasive water jet cutting methods for reducing blast-induced ground vibration in tunnel excavation[J]. International Journal of Rock Mechanics & Mining Sciences, 2015, 75:147-158.
[8] Jh N, A G. An analytical and experimental investigation of the velocities of particles entrained by the gas flow in nozzles[J]. Journal of Fluid Mechanics, 1968, 33(1):131-149.
[9] Stevenson A N J, Hutchings I M. Scaling laws for particle velocity in the gas-blast erosion test[J]. Wear, 1995, 181(95):56-62.
[10] Li H Z, Wang J, Fan J M. Analysis and modelling of particle velocities in micro-abrasive air jet[J]. International Journal of Machine Tools & Manufacture, 2009, 49(11):850-858.
[11] 王瑞和,仲冠宇,周卫东,李罗鹏,杨焕强,王方祥. 基于基因表达式编程算法的磨料射流切割深度预测模型[J]. 中国石油大学学报(自然科学版),2015,01:60-65
WANG Rui-he，ZHONG Guan-yu，ZHOU Wei-dong，et al． A model for predicting cutting depth of casing using AWJ technique based on gene expression programming algorithm［J］.Journal of China University of Petroleum( Edition of Natural Science),2015,39( 1) : 60-65．.
[12]董星,马安昌,吴财芳,韩建勇. 基于神经网络的前混合磨料射流切割深度的研究[J]. 煤炭学报,2002,04:430-433.
DONG Xing, MA An-chang, WU Cai-fang, et al. Neural network method and the study of the cut depth of DIA jet[J]. Journal of China Coal Society, 2002.
[13]周卫东,王瑞和,杨永印,步玉环,曹砚峰. 前混式磨料水射流切割套管的深度计算模型[J]. 石油大学学报(自然科学版),2001,02:3-5+11.
Zhou W D, Wang R H, Yang Y Y, et al. Models for calculating cutting depth of casing by premixing abrasive water jet[J]. Journal of the University of Petroleum China, 2001.
[14]林晓东,卢义玉,汤积仁,敖翔,张磊. 基于SPH-FEM耦合算法的磨料水射流破岩数值模拟[J]. 振动与冲击,2014,18:170-176.
LIN Xiao-dong,LU Yi-yu,TANG Ji-ren, et al. Numerical simulation of abrasive water jet breaking rock with SPH-FEM coupling algorithm[J]. Journal of Vibration & Shock, 2014, 33(18):170-176.
[15]汤积仁,卢义玉,孙惠娟,葛兆龙,夏彬伟,李倩. 基于CT方法的磨料射流冲蚀损伤岩石特性研究[J]. 岩石力学与工程学报,2016,02:297-302.
TANG Ji-ren, LU Yi-yu,SUN Hui-juan, , et al. Study of erosion and damage characteristics of rock by abrasive water jet using CT[J]. 2016, 02: 297-302.
[16]沈忠厚．水射流理论与技术[M]．东营: 石油大学出版社, 1998. 293- 327.
Shen Zhong-Hou. Theory and technology of water jet [M].Petroleum University Press, 1998,p293-327.
[17]李晓红, 卢义玉, 向文英, 等. 水射流理论及在矿业工程中的应用[M]. 重庆大学出版社, 2007, 39-40.
Li Xiao-hong,Lu Yi-yu ,Xiang Wen-ying. Water jet theory and its application in mining engineering[M].Chongqing University Press, 2007,p39-40.
[18]Rajaratnam N. Turbulent Jets[J]. Developments in Water Science, 1976, 5(76):77–82.
[19]L, Boguslawski, and P. Co. "Flow structure of the free round turbulent jet in the initial region." Journal of Fluid Mechanics 90.3(1979):531-539.
[20] Abramovich G, Schindel L. General properties of turbulent jets[M]. MIT press, 1963. [19]
[21] Albertson M L, Dai Y B, Jensen R A, et al. Diffusion of submerged jets[J]. Transactions of the American Society of Civil Engineers, 1950, 115(1): 639-664.
[22] Crow S C, Champagne F H. Orderly structure in jet turbulence[J]. Journal of Fluid Mechanics, 1971, 48(03): 547-591.
[23] Bush W B, Krishnamurthy L. Asymptotic analysis of the fully developed region of an incom-pressible, free, turbulent, round jet[J]. Journal of Fluid Mechanics, 1991, 223: 93-111.
[24]王明波，王瑞和. 喷嘴内液固两相射流流场的数值模拟[J]. 石油大学学报(自然科学版) ,2005,05: 46-49.
WANG Ming-bo,WANG Rui-h.Numerical simulation on fluid-particle two-phase jet flow field in nozzle[J] ．Journal of the University of Petroleum , China，2005，05：46-49．
[25]Moris,S.A.,Alexander,A.J..An Investigation of Particle Trajectories in Two Phase Flow System[J].J.Fluid Mech.,Vol.55,No.2,(1972),p.193.
[26]左伟芹, 王晓川, 郝富昌,等. 基于迭代算法的磨料颗粒加速机制研究[J]. 中国石油大学学报自然科学版, 2016, 40(4):104-109.
Zuo Wei-qin,Wang Xiao-chuan,Hao Fu-chang, et al. Research on acceleration mechanism of abrasive in pre-mixed abrasive water-jet based on iterative algorithm[J].Journal of China University of Petroleum, 2016, 40(4):104-109.
[27]章文峰,卢义玉,汤积仁,黄飞. 基于PIV技术的磨料水射流中固体磨料粒子速度分布实验研究[J]. 振动与冲击,2016,08:159-165+186.
ZHANG Wen-feng，LU Yi-yu，TANG Ji-ren,et al. Experimental study of velocity distribution of solid abrasive particles in abrasive water jets based on PIV technology[J].JOURNAL OF VIBRATION AND SHOCK, 2016,08:159-165+186.