考虑实测基节误差的修形齿轮啮入冲击计算

PDF(1997 KB)

振动与冲击 ›› 2018, Vol. 37 ›› Issue (22) : 30-35.

论文

考虑实测基节误差的修形齿轮啮入冲击计算

郭芳，方宗德，张西金

作者信息 +

Calculation on the meshing-in impact of a modified gear considering the measured pitch error

GUO Fang, FANG Zongde, ZHANG Xijin

Author information +

文章历史 +

摘要

为研究制造误差对齿轮系统啮入冲击的影响，给出一种考虑实测基节误差的齿轮啮入冲击算法。该算法基于考虑实测基节误差的轮齿接触分析(TCA, Tooth Contact Analysis)及轮齿承载接触分析(LTCA, Loaded Tooth Contact Analysis)，准确算出齿轮连续啮合过程中每对啮合轮齿的实际啮入点位置；并根据LTCA得到的轮齿承载变形及载荷分配系数，计算出当前啮入齿对啮入点处的刚度；最后计算出以n个啮合周期为一个大周期的啮入冲击力（n为主、被动轮齿数的最小公倍数）。研究表明，在不同齿对的相对基节误差具有随机性的情况下，该算法可以准确算出每对轮齿的线外啮入点的位置，并相应算出不同位置的啮入点的刚度；该算法适用于具有修形齿面或误差齿面的齿轮系统，真实反映了实测基节误差对齿轮啮入冲击的影响。

Abstract

An algorithm for studying the gear meshing-in impact considering the measured pitch error was proposed to analyse the effect of manufacturing errors on the meshing-in impact.Based on the tooth contact analysis (TCA) and loaded tooth contact analysis (LTCA) considering the measured pitch error, by the algorithm the actual position of the meshing-in contactin gear meshing was calculated precisely.Next, according to the LTCA-calculated tooth deformation and load sharing factor between teeth, the teeth stiffness at the meshing-in point of the current mating teeth was obtained.Then, the meshing-in impact in a big cycle of n meshing periods (n is the least common multiple of the teeth number of pinion and gear) was analyzed.The study shows that, in the situation of random relative pitch error, by the algorithm the position of the corner contact in gear meshing-in and the corresponding stiffness can be acquired exactly.The algorithm is suitable for the modified tooth surfaces or error surfaces of gear systems.The result really reflect the effect of measured pitch error on the meshing-in impact.

导出引用

郭芳，方宗德，张西金. 考虑实测基节误差的修形齿轮啮入冲击计算[J]. 振动与冲击, 2018, 37(22): 30-35

GUO Fang, FANG Zongde, ZHANG Xijin. Calculation on the meshing-in impact of a modified gear considering the measured pitch error[J]. Journal of Vibration and Shock, 2018, 37(22): 30-35

参考文献

[1] 符双学, 周长江. 基于精确建模的齿轮传动线外啮合冲击研究[J]. 中国工程机械学报, 2016, 14(3): 221-226.
FU Shuangxue, ZHOU Changjiang. Corner contact impact on gear transmission based on accurate modeling [J]. Chinese Journal of Construction Machinery, 2016, 14(3): 221-226.
[2] 周长江, 唐进元, 钟志华. 齿轮传动的线外啮合与冲击摩擦[J]. 机械工程学报, 2008, 44(3): 75-81.
ZHOU Changjiang, TANG Jinyuan, ZHONG Zhihua. Corner contact and impact friction of gear drive [J]. Chinese Journal of Mechanical Engineering, 2008, 44(3): 75-81.
[3] 周长江, 张成, 唐进元. 齿轮传动线外啮出冲击建模与计算[J]. 航空动力学报, 2014, 29(5): 1205-1210.
ZHOU Changjiang, ZHANG Cheng, TANG Jinyuan. Modeling and calculation of impact of mesh-out at corner contact in gear drive [J]. Journal of Aerospace Power, 2014, 29(5): 1205-1210.
[4] 武宝林, 杨素君, 姚俊红. 齿轮传动中啮合冲击的理论分析[J]. 机械科学与技术, 2003, 22(1): 55-57.
WU Baolin, YANG Sujun, YAO Junhong. Theoretical analysis on meshing impact of involute gears [J]. Mechanical Science and Technology, 2003, 22(1): 55-57.
[5] 唐进元, 刘欣, 戴进. 基于ANSYS/LS-DYNA的齿轮传动线外啮合冲击研究[J]. 振动与冲击, 2007, 26(9): 41-50.
TANG Jinyuan, LIU Xin, DAI Jin. Study on corner contact shock of gear transmission by ANSYS/LS-DYNA soft wear [J]. Journal of Vibration and Shock, 2007, 26(9): 41-50.
[6] 佟操, 孙志礼, 冯真, 等. 基于Pro/E和LS-DYNA的齿轮线外啮合冲击研究[J]. 机械与电子, 2014, (6): 10-14.
TONG Cao, SUN Zhili, FENG Zhen, et al. Research of gear meshing impact outside the engagement line based on Pro/E and LS-DYNA [J]. Machinery & Electronics, 2014, (6): 10-14.
[7] LIN H, WANG J, OSWALD F, et al. Effect of extended tooth contact on the modeling of spur gear transmissions [C] // Prepared for the 29th Joint Propulsion Conference and Exhibit, Monterey, California, 1993:1-12.
[8] DEVLIN M T, JAO T C, MILNER J, et al. Influence of surface roughness on gear pitting behavior [J]. 2006, may/june:30-38
[9] 戴麟. 相位调谐与啮入冲击对行星齿轮系统辐射噪声影响的研究[D]. 南京: 南京航空航天大学, 2016.
DAI Lin. Research on the effect of phase adjustment and meshing impact on noise radiation in planetary gear transmission [D]. Nanjing: Nanjing University of Aeronautics and Astronautics, 2016.
[10] 方宗德. 修形斜齿轮的承载接触分析[J]. 航空动力学报, 1997, 12(3): 251-254.
FANG Zongde. Tooth contact analysis of modified helical gears [J]. Journal of Aerospace Power, 1997, 12(3): 251-254.
[11] 方宗德, 邓效忠, 任东峰. 考虑边缘接触的弧齿锥齿轮承载接触分析[J]. 机械工程学报, 2002, 38(9): 69-72.
FANG Zongde, DENG Xiaozhong, REN Dongfeng. Loaded tooth contact analysis of spiral bevel gears considering edge contact [J]. Chinese Journal of Mechanical Engineering, 2002, 38(9): 69-72.
[12] 王成, 方宗德, 谷建功, 等. 人字齿轮承载接触分析与试验[J]. 航空动力学报, 2010, 25(3): 718-722.
WANG Cheng, FANG Zongde, GU Jiangong, et al. Loaded tooth contact analysis of double helical gears and experimental investigation [J]. Journal of Aerospace Power, 2010, 25(3): 718-722.
[13] 赵宁, 郭辉, 方宗德, 等. 直齿面齿轮修形及承载接触分析[J]. 航空动力学报, 2008, 23(11): 2142-2146.
ZHAO Ning, GUO Hui, FANG Zongde, et al. Modification and loaded contact analysis of spur face gears [J]. Journal of Aerospace Power, 2008, 23(11): 2142-2146.
[14] 方宗德. 修形斜齿轮的轮齿接触分析[J]. 航空动力学报, 1997, 12(3): 247-250.
FANG Zongde. Tooth contact analysis of modified helical gears [J]. Journal of Aerospace Power, 1997, 12(3): 247-250.
[15] 邓效忠, 方宗德, 任东峰, 等. 弧齿锥齿轮的齿距误差对传动性能的影响研究[J]. 航空动力学报, 2002, 17(2): 268-272.
DENG Xiaozong, FANG Zongde, REN Dongfeng, et al. Study on contact ratio of spiral bevel gears and influence of pitch error [J]. Journal of Aerospace Power, 2002, 17(2): 268-272.
[16] 张金梅, 刘更, 周建星, 等. 考虑啮入冲击作用下减速器的振动噪声分析[J]. 振动与冲击, 2013, 32(13): 118-141.
ZHANG Jinmei, LIU Geng, ZHOU Jianxing, et al. Vibration and noise radiation analysis for a gear reducer considering meshing impact [J]. Journal of Vibration and Shock, 2013, 32(13): 118-141.