采用虚拟样机技术建立过山车轨道与列车模型并进行运行仿真,保证了数字样机符合游乐设施安全规范要求,但是在进行过山车实际安装过程中,难以保证物理样机与数字模型完全一致,在实际工况下与仿真运行结果也会有一定的偏差,因此必须对物理样机进行测试,依据采集的数据应用Matlab进行分析,找出不合格数据点,判断不合格数据点的位置,指导设计人员针对性的改进过山车轨道,并进行反复检测分析与调整轨道,直到达到安全标准的要求。
Abstract
Virtual prototype technology was adopted to establish the model of a roller coaster track and train. Then the operation simulation was done with the model to ensure the digital prototype to meet the requirements of the safety standard of entertainment equipment. But in the actual installation process of a roller coaster, it was difficult to guarantee the physical prototype and its digital model to agree well, the operation state under the actual working condition and the simulation result had a certain deviation. The physical prototype was tested to measure its accelerations. The acceleration data collected were analyzed with MATLAB to find out unqualified data points, and judge their locations. The designers were guided to improve pertinently the roller coaster track with repeatedly tests and analyses, and adjusting the track until it met the requirements of the safety standard.
关键词
过山车 /
加速度 /
Matlab /
安全标准
{{custom_keyword}} /
Key words
roller coaster /
acceleration /
MATLAB /
safety standard
{{custom_keyword}} /
{{custom_sec.title}}
{{custom_sec.title}}
{{custom_sec.content}}
参考文献
[1] 杨振业.大型滑行类游乐设备的建模与仿真[D].广东:华南理工大学,2011:1-3.
YANG Zhen-ye.The modeling and simulation of large sliding class amusement equipment [D].Guangdong:South China University of Technology,2011:1-3.
[2] GB8408-2008游乐设施安全规范[S]中国国家标准化管理委员会,2008.
GB8408-2008 Amusement device safety code [S]China national standardization management committee,2008.
[3] 银明,杨瑞刚,杨明亮.基于SolidWorks的过山车轨道三维建模仿真[J].起重运输机械,2012(6):65-66.
YIN Ming, YANG Rui-gang, YANG Ming-liang.Based on the SolidWorks of a roller coaster track 3d modeling and simulation [J].Lifting transportation machinery, 2012(6):65-66.
[4] 刘忠胜,于泽涛,屈福政.过山车动态仿真建模方法[J].冶金设备,2009,S1:30-31.
LIU Zhong-sheng, YU Ze-tao, QU Fu-zheng. Roller coaster dynamic simulation modeling method [J].Metallurgical equipment, 2009(S1):30-31.
[5] 汪惠群,郑建荣.基于虚拟样机的风力作用下过山车动态性能研究[J].机械设计,2007,24(9):35-37.
WANG Hui-qun, ZHENG Jian-rong. Based on the virtual prototype of the wind to study the dynamic performance under the action of a roller coaster [J],2007,24(9):35-37.
[6] 陈礼,关伟.过山车动力学建模与仿真[J].中国工程机械学报,2010,8(4):400-402.
CHEN Li,GUAN Wei.Roller coaster dynamics modeling and simulation [J]Chinese journal of construction machinery, 2010,8(4):400-402.
[7] 肖立波,任建亭,杨海峰.振动信号预处理方法研究及其MATLAB实现[J].计算机仿真,2010,27(08):330-333.
XIAO Li-bo, REN Jian-ting, YANG Hai-feng. Study on Vibration Signal processing Method Based on MATLAB [J]. Computer Simulation,2010,27(08):330-333.
[8] 王济,胡晓.MATLAB在振动信号处理中的应用[M].北京:中国水利水电出版社,2006: 84-86.
Wang Ji, HU Xiao.Application of Matlab in Data processing of tremor signals observation [M].Beijing:China water conservancy and hydropower press,2006: 84-86.
{{custom_fnGroup.title_cn}}
脚注
{{custom_fn.content}}