高速角接触球轴承保持架不稳定运动机理分析

张涛 1, 陈晓阳 1,顾家铭 2,赵利锋 3

振动与冲击 ›› 2019, Vol. 38 ›› Issue (10) : 233-241.

PDF(2348 KB)
PDF(2348 KB)
振动与冲击 ›› 2019, Vol. 38 ›› Issue (10) : 233-241.
论文

高速角接触球轴承保持架不稳定运动机理分析

  • 张涛 1, 陈晓阳 1,顾家铭 2,赵利锋 3
作者信息 +

Analysis on the unstable movement mechanism of high-speed angular contact ball bearing cages

  • ZHANG Tao 1  CHEN Xiaoyang 1  GU Jiaming 2  ZHAO Lifeng 3
Author information +
文章历史 +

摘要

建立了球和保持架六自由度的角接触球轴承动力学为基础的磨损仿真模型。以某仪表转子轴承为算例,分析了不同载荷工况和保持架间隙比下保持架的运动,从球与保持架兜孔碰撞点位置、碰撞力的大小和频率等方面探讨了保持架不稳定运动的机理。发现在纯轴向载荷下,因球与兜孔碰撞点位置的不同,保持架会沿轴向摆动;轴向径向联合载荷作用下,因球的轨道速度随接触角变化,球与保持架碰撞力和频率都增加,导致保持架的运动不稳定;轴向和旋转径向负荷下,保持架兜孔间隙与挡边间隙比B/R小于1时,保持架质心运动轨迹接近于圆形,保持架的离心力作用于球上增大了球与兜孔的碰摩;间隙比大于1时,保持架质心轨迹为多边形或无规律涡动,引导挡边对保持架的约束减小了球与兜孔的相互作用,保持架兜孔的磨损率较低。圆形的质心轨迹是保持架稳定运动的一种状态,但从保持架磨损和能耗的角度看,对保持架的磨损寿命不利。

Abstract

A dynamic wear simulation model for angular contact ball bearings with six-degree-of-freedom ball and cage was established.Taking a certain instrument rotor ball bearing as an example, the cage motion under different load conditions and cage clearance ratios was analyzed.The mechanism of the cage unstable motion was discussed from the aspects of the ball-pocket collision, and the magnitude and frequency of the impact force.It is found that under the pure axial load, the cage will swing along the axial direction due to the ball-pocket collision at different positions.Under the joint of axial and radial loads, the orbital velocity of the ball varies with the contact angle, and the collision force and frequency of the ball and cage increase, resulting in the unstable motion of the cage.Under the axial and rotating radial load, when the ratio of the ball-pocket clearance to the cage-guide land clearance B/R is less than 1, the orbit of the cage mass center whirl is close to a circle.The centrifugal force of the cage acts on the ball, resulting in an increase in the ball-pocket collision.When the clearance ratio is greater than 1, the centroid trajectory of the cage is polygonal or irregular, and the constraint of the guide land on the cage reduces the interaction between the ball and cage, so the wear rate of the cage is lower.The circular centroid trajectory is a state of stable motion of the cage, but from the perspective of cage wear and energy loss, it is unfavorable for the wear life of the cage.

关键词

角接触球轴承 / 动力学 / 保持架稳定性 / 碰撞 / 磨损率

Key words

angular contact ball bearings / dynamics / cage stability / collision / wear rate

引用本文

导出引用
张涛 1, 陈晓阳 1,顾家铭 2,赵利锋 3. 高速角接触球轴承保持架不稳定运动机理分析[J]. 振动与冲击, 2019, 38(10): 233-241
ZHANG Tao 1 CHEN Xiaoyang 1 GU Jiaming 2 ZHAO Lifeng 3 . Analysis on the unstable movement mechanism of high-speed angular contact ball bearing cages[J]. Journal of Vibration and Shock, 2019, 38(10): 233-241

参考文献

[1] 刘春浩, 顾家铭, 周赤忠, 等. 陀螺仪电动机转子轴承研究现状与展望[J]. 机械工程学报, 2006, 42(11):17-25.
 LIU Chunhao, GU Jiaming, ZHOU Chizhong, et al. Research of present state and prospective on gyro-spin bearings[J]. Journal of Mechanical Engineering, 2006, 42(11):17-25.
[2] WALTERS C T. The dynamics of ball bearings[J]. Journal of Lubrication Technology, 1971, 93:1-10.
[3] KANNEL J W, BUPARA S S. A simplified model of cage motion in angular contact bearings operating in the EHD lubrication regime[J]. Journal of Lubrication Technology, 1978, 100:395-403.
[4] GUPTA P K. Dynamic of rolling-element bearings-Part 3, 4[J]. Journal of Lubrication Technology, 1979, 101:312-326.
[5] MEEKS C R, NG K O. The dynamics of ball separators in ball bearings-Part 1, 2[J]. ASLE Transaction, 1985, 28(3):277-295.
[6] GUPTA P K, DILL J F, Bandow H E. Dynamics of rolling element bearings experimental validation of the DREB and RAPIDREB computer programs[J]. Journal of Tribology, 1985, 107:132-137.
[7] GUPTA P K. Frictional instabilities in ball bearings[J]. Tribology Transctions, 1988, 31(2) :258-268.
[8] GUPTA P K. Dynamic loads and cage wear in high-speed rolling bearings[J].Wear, 1991, 147:119-134.
[9] GUPTA P K. Modeling of instabilities induced by cage clearances in ball bearings[J]. Tribology Transaction, 1991, 34(1):93-99.
[10] GUPTA P K. Cage Unbalance and Wear in Ball Bearings [J].Wear, 1991, 147:93-104.
[11] ASHTEKAR A, SADEGHI F, STACKE L E. A new approach to modeling surface defects in bearing dynamic simulations[J]. Journal of Tribology, 2008, 130:041103-1-8.
[12] WEINZAPFEL N, SADEGHI F. A discrete element approach for modeling cage flexibility in ball bearing dynamic simulations[J]. Journal of Tribology, 2009, 131:021102-1-11.
[13] GUPTA P K. Current status of and future innovations in rolling bearing modeling[J]. Tribology Transactions, 2011, 54:394-403.
[14] LIU Xiuhai, DENG Sier, TENG Hongfei. Dynamic stability analysis of cage in high-speed oil-lubricated angular contact ball bearings[J]. Transactions of Tianjin University, 2011, 17(1):20-27.
[15] YE Zhenhuan, WANG Liqin. Cage instabilities in high-speed ball bearings[J]. Applied Mechanics and Materials, 2013, 278:3-6.
[16] 邓四二, 谢鹏飞, 杨海生, 等. 高速角接触球轴承保持架柔体动力学分析[J]. 兵工学报, 2011, 32(5):625-631.
 DENG Sier, XIE Pengfei, YANG Haisheng, et al. Flexible-body dynamic analysis on cage of high-speed angular contact ball bearing[J]. Acta Armamentarii, 2011, 32(5):625-631.
[17] 崔立, 时大方, 郑建荣, 等. 基于ANSYS/LS-DYNA的保持架动力学分析[J]. 机械传动, 2012, 36(6):78-81.
 CUI Li, SHI Dafang, ZHENG Jianrong, et al. Dynamic analysis of cage based on ANSYS/LS-DYNA[J]. Journal of Mechanical Transmission, 2012, 36(6):78-81.
[18] 姚廷强, 王立华, 刘孝保,等. 变工况下角接触球轴承保持架稳定性分析[J]. 振动与冲击, 2016, 35(18): 172-180.
 YAO Tingqiang, WANG Lihua, LIU Xiaobao, et al. Dynamic stability analysis on the of ball bearing under varying working environment[J]. Journal of Vibration and Shock, 2016, 35(18): 172-180.
[19] KINGSBURY E P. Torque variations in instrument ball bearings[J]. ASLE Transactions. 1965, 8:435-441.
[20] KINGSBURY E P, WALKER R. Motions of an unstable retainer in an instrument ball bearing[J]. Journal of Tribology. 1994, 116:202-208.
[21] GUPTA P K. Advanced dynamic of rolling elements, New York:Springer-Verlag, 1984.
[22] ZHANG Tao, CHEN Xiaoyang, GU Jiaming et al. Influence of preload on the friction and wear properties of high-speed instrument angular contact ball bearings[J]. Chinese Journal of Aeronautics, 2017.
[23] GUPTA P K, FORSTER N H. Modeling of wear in a solid-lubricated ball bearing[J]. Tribology Transactions, 1987, 30(1):55-62.
[23] HOUPERT L. Ball bearing and tapered roller bearing torque: analytical, numerical and experimental results[J]. Tribology Transactions, 2002, 45(3):345-353.
[25] TALLIAN T E. Rolling bearing life prediction: Corrections for material and operating conditions-Part 2: The correction factors[J]. Journal of Tribology, 1988, 110:7-12.

PDF(2348 KB)

Accesses

Citation

Detail

段落导航
相关文章

/