基于分形理论的结合面法向接触刚度模型

PDF(1187 KB)

振动与冲击 ›› 2019, Vol. 38 ›› Issue (8) : 218-224.

论文

基于分形理论的结合面法向接触刚度模型

陈虹旭，董冠华，殷勤，谭峰，殷国富

作者信息 +

A normal contact stiffness model of joint surface based on the fractal theory

CHEN Hongxu DONG Guanhua YIN Qin TAN Feng YIN Guofu

Author information +

文章历史 +

摘要

基于修正的分形理论，以尺度系数定义微凸体大小，在充分考虑微凸体接触变形过程的基础上，对赫兹接触模型进行补偿修正，建立了结合面法向接触刚度模型，研究了法向接触刚度与分形维度之间的关系，并进行了仿真；以螺栓结合面为实验对象，采用结构函数法获取分形参数，进而求出结合面法向接触刚度值并录入有限元模型，在此基础上应用m+p噪声振动测试系统开展模态实验，通过对比理论模态与实验模态的振型和固有频率来验证理论模型的正确性；实验和仿真结果表明：理论模型和实验模型前8阶模态的振型一致，前8阶固有频率误差在-10.2%～-1%以内。

Abstract

A joint surface normal contact stiffness model was established.The model was based on the modified fractal theory and the size of asperity was defined by the scaling factor.Considering the contact deformation process of asperity, an error compensation method was used to correct the Hertz contact model.Numerical simulation was carried out to obtain the relations between normal contact stiffness and the fractal dimension.A bolt joint surface experiment was carried out to verify the correctness of the theoretical model.Firstly, according to the measured fractal parameters of the bolt joint surface, normal contact stiffness was solved.Then a modal experiment was carried out by using m+p noise and a vibration testing system.Finally, the results of the experiment and the finite element simulation were compared.The experiment results show that the first 8 modal shapes of the theoretical model and the experimental model are the same, and the error of the natural frequencies are within the range of -10.2%—-1%.

导出引用

陈虹旭，董冠华，殷勤，谭峰，殷国富 . 基于分形理论的结合面法向接触刚度模型[J]. 振动与冲击, 2019, 38(8): 218-224

CHEN Hongxu DONG Guanhua YIN Qin TAN Feng YIN Guofu. A normal contact stiffness model of joint surface based on the fractal theory[J]. Journal of Vibration and Shock, 2019, 38(8): 218-224

参考文献

[1] 邓聪颖，殷国富，肖红，等. 基于能量分布的机床整机动态特性优化方法[J]. 振动.测试与诊断. 2015(06): 1083-1089.
Deng Congying，Yin Guofu，Xiao Hong，et al. Dynamic characteristics optimization for whole machine toll based on energy distribution [J]. Journal of Vibration, Measurement & Diagnosis, 2015(06): 1083-1089.
[2] 董冠华，殷勤，殷国富，等. 机床结合部动力学建模与辨识方法的研究[J]. 机械工程学报. 2016(05): 162-168.
Dong Guanhua，Yin Qin，Yin Guofu，et al. Research on dynamics modeling and identification of machine tool joints [J]. Journal of Mechanical Engineering, 2016(05): 162-168.
[3] 张学良，陈永会，温淑花，等. 考虑弹塑性变形机制的结合面法向接触刚度建模[J]. 振动工程学报. 2015(01): 91-99.
Zhang Xueliang，Chen Yonghui，Wen Shuhua，et al. The model of normal contact stiffness of joint interfaces incorporating elastoplastic deformation mechanism[J]. Journal of Vibration Engineering, 2015(01): 91-99.
[4] 温淑花，张宗阳，张学良，等. 固定结合面刚度分形模型[J]. 农业机械学报. 2013(02): 255-260.
Wen Shuhua，Zhang Zongyang，Zhang Xueliang，et al Stiffness fractal model for fixed joint interfaces[J]. Transactions of the Chinese Society for Agricultural Machinery,2013(02): 255-260.
[5] 缪小梅，黄筱调，袁鸿. 考虑微凸体弹塑性变形的结合面分形接触模型[J]. 农业机械学报. 2013(01): 248-252.
Mou Xiaomei，Huang Xiaodiao，Yuan Hong. Fractal contact model of joint interfaces considering elastic-plastic deformation of asperities[J]. Transactions of the Chinese Society for Agricultural Machinery, 2013(01): 248-252.
[6] 李小彭，王雪，运海萌，等. 三维分形固定结合面法向接触刚度的研究[J]. 华南理工大学学报(自然科学版). 2016(01): 114-122.
Li Xiaopeng，Wang Xue，Yun Haimeng，et al. Investigation into normal contact stiffness of fixed joint surface with three-dimensional fractal[J].Journal of South China University of Technology, 2016(01): 114-122.
[7] 兰国生，张学良，丁红钦，等. 基于分形理论的结合面改进接触模型[J]. 农业机械学报. 2011(10): 217-223.
Lan Guosheng，Zhang Xueliang，Ding Hongqin，et al. Modified contact model of joint interfaces based on fractal theory[J]. Transactions of the Chinese Society for Agricultural Machinery, 2011(10): 217-223.
[8] Morag Y, Etsion I. Resolving the contradiction of asperities plastic to elastic mode transition in current contact models of fractal rough surfaces[J]. Wear. 2007, 262(5-6): 624-629.
[9] Majumdar A, Bhushan B. Fractal Model of Elastic-Plastic Contact Between Rough Surfaces[J]. Journal of Tribology. 1991.
[10] Greenwood J A, Williamson J B P. Contact of Nominally Flat Surfaces[J]. Proceedings of the Royal Society A: Mathematical, Physical and Engineering Sciences. 1966, 295(1442): 300-319.
[11] 刘正林. 摩擦学原理[M]. 北京: 高等教育出版社, 2009: 224.
[12] Yan W, Komvopoulos K. Contact analysis of elastic-plastic fractal surfaces[J]. Journal of Applied Physics. 1998, 84(7): 3617-3624.
[13] Komvopoulos K, Ye N. Three-Dimensional Contact Analysis of Elastic-Plastic Layered Media With Fractal Surface Topographies[J]. Journal of Tribology. 2001.
[14] Wang S, Komvopoulos K. A Fractal Theory of the Interfaoial Temperature Distribution in the Slow Sliding Regime: Part I — Elastic Contact and Heat Transfer Analysis[J]. Journal of Tribology. 1994.
[15] Pullen J, Williamson J B P. On the Plastic Contact of Rough Surfaces[J]. Proceedings of the Royal Society A: Mathematical, Physical and Engineering Sciences. 1972, 327(1569): 159-173.
[16] 谭峰，殷国富，董冠华，等. 基于子结构综合法的螺栓结合部切向动刚度优化辨识[J]. 四川大学学报(工程科学版). 2015(S2): 171-177.
Tan Feng，Yin Guofu，Dong Guanhua，et al. Optimized identification of bolt joint’ s tangential dynamic stiffness based on the substructure synthesis method [J]. Journal of Sichuan University, 2015(S2): 171-177.