为了研究蝴蝶形钢板剪力墙-自复位结构体系的抗震性能，对7个两层单跨1/2缩尺蝴蝶形钢板的自复位钢框架试件进行了低周反复荷载试验。根据试验结果着重分析了蝴蝶形钢板的高厚比、高宽比和蝴蝶杆层数以及试件的初始预应力等参数对试件的承载力、滞回性能、耗能能力和复位效果等性能的影响。试验结果表明：随着钢板的高厚比和高宽比的减小，试件的承载力和耗能能力增大，但残余变形随着高厚比减小而增加，且几乎不受高宽比的影响；蝴蝶杆层数越多，试件的承载力和残余变形越大，前期耗能越迅速，但最终耗能量相同；初始预应力越大，试件的承载力越大，耗能能力越弱，残余变形越小。
Abstract
In order to investigate the seismic performance of a self-centering steel frame in-filled with butterfly-shaped steel plate walls, seven one-bay two-story large-scale structure specimens subjected to cyclic loading were tested.Based on the test results, the effects of the height to thickness ratio, height to width ratio of plate walls, the number of butterfly link stories of plate walls and the initial prestress on the load-carrying capacity, hysteretic behavior, energy-dissipation capacity and self-centering ability of specimens were studied.The experimental results show that the load-carrying capacity and energy-dissipation capacity of specimens are augmented with the increase of height to thickness and height to wide ratios of the plates.However, due to the increase of height to thickness ratio of the plates, the residual deformation of specimens increases obviously, while the height to width ratio of the plates has ignorable effect on it.The specimens with two link stories of in-filled plates are of larger load-carrying capacity and greater permanent deformation with an advantage of earlier energy-dissipation behavior of plates, but the final amount of consumed energy is identical.Besides, for those specimens with relatively larger prestress in strands, more robust load-carrying capacity, weaker energy-dissipation behavior and smaller residual deformation are observed.
关键词
自复位 /
抗震性能 /
蝴蝶形钢板剪力墙 /
滞回性能 /
残余变形
{{custom_keyword}} /
Key words
self-centering /
seismic performance /
butterfly-shaped steel plate shear wall /
hysteretic behavior;residual deformation
{{custom_keyword}} /
{{custom_sec.title}}
{{custom_sec.title}}
{{custom_sec.content}}
参考文献
[1] Clayton P M. (2010). Self-centering steel plate shear walls: Development of design procedure and evaluation of seismic performance. Master’s thesis, Civil and Environmental Engineering Dept. Univ. of f Washington Seattle,WA.
[2] Clayton P M, Berman J W, Lowes L N. Seismic design and performance of self-centering steel plate shear walls. Journal of Structural Engineering, 2012, 138(1): 22–30.
[3] Clayton P M, Berman J W and Lowes L N. (2012a). Performance Based Design and Seismic Evaluation of Self-Centering Steel Plate Shear Walls. Journal of Structural Engineering,ASCE,Vol. 138,Issue 1,22-30.
[4] Clayton P M, Winkley T B, Berman J W, Lowes L N. Experimental investigation of self-centering steel plate shear walls[J]. Journal of Structural Engineering, 2012, 138(7): 952-960.
[5] Clayton P M, Berman,J, Wand Lowes L N. (2013). Subassembly Testing and Modeling of Self-centering Steel Plate Shear Walls. Engineering Structures,Vol. 56, 1848-1857.
[6] Clayton P M, Berman J W, Lowes L N. Seismic performance of self-centering steel plate shear walls with beam-only-connected web plates. Journal of Constructional Steel Research, 2015, 106: 198– 208.
[7] Dowden D M, Purba R, Bruneau M. Behavior of self-centering steel plate shear walls and design considerations[J]. ASCE Journal of Structural Engineering, 2012, 138（1）：11-21.
[8] Dowden D M, Bruneau M. Analytical and Experimental Investigation of Self-Centering Steel Plate Shear Walls. Tech. Rep. MCEER-14–0010, Multidisciplinary Center for Earthquake Engineering Research, State University of New York Buffalo, Buffalo, NY, 2014.
[9] Dowden D M. Resilient Self-Centering Steel Plate Shear Walls. Dissertation for the Doctoral Degree. Buffalo, NY: University at Buffalo, 2014.
[10] Dowden D M, Clayton P M, Li C H, Berman J W, Bruneau M, Lowes L N, and Tsai K C. (2016), Full-scale Pseudo-Dynamic Testing of self-centering steel plate shear wall. journal of structure engineering, ASCE, Vol. 142, No.1, doi: 10.1061/(ASCE) ST. 1943-541X. 0001367.
[11] Dowden D M, Bruneau M. Kinematics of self-centering steel plate shear walls with NewZ-BREAKSS post-tensioned rocking connection. AISC Engineering Journal, 2016, 53(3): 117–136.
[12] Daniel M. Dowden, Michel Bruneau. (2016), Dynamic Shake-Table Testing and Analytical Investigation of Self-Centering Steel Plate Shear Walls[J]. journal of structure engineering, ASCE, Vol. 142, No. 1, doi: 10. 1061/(ASCE)ST. 1943-541X. 0001547.
[13] 经聪.利于蝴蝶形钢板剪力墙耗能的自复位结构体系研究[D]. 苏州: 苏州科技学院, 2013.
Jing Cong. Study on Self-centering system dissipating
energy with butterfly-shaped plate shear wall. [D]. Jiangsu: Suzhou University of Science and Technology, 2013.
[14] 王阳. 多层钢板剪力墙自复位结构性能研究[D]. 苏州: 苏州科技大学, 2017.
Wang Yang. Research on performance of multilayer self-centering steel plate shear wall structure [D]. Jiangsu: Suzhou University of Science and Technology, 2017.
[15] 吴笑. 单个蝴蝶形钢板剪力墙-自复位钢框架结构体系的试验研究[D]. 苏州: 苏州科技大学, 2018.
Wuxiao. Experimental study on self-centering structure systems equipped with single butterfly-shaped steel plate shear wall. [D]. Jiangsu: Suzhou University of Science and Technology, 2018.
[16] 张萍. 利用蝴蝶形钢板墙耗能的自复位结构体系试验研究[D]. 苏州: 苏州科技大学, 2018.
Zhang Ping. Experimental study of seismic performance of self-centering steel frame with butterfly-shaped steel plate wall. [D]. Jiangsu: Suzhou University of Science and Technology, 2018.
[17] 马磊，李启才. 蝴蝶形钢板墙的抗侧刚度和承载力研究[J]. 苏州科技学院学报(工程技术版), 2015, (28): 30-36.
MA Lei, LI Qicai. Initial stiffness and bearing capacity of the butterfly-shaped steel plate walls. [J]. Journal of Suzhou University of Science and Technology (Engineering and Technology), 2015, (28): 30-36.
[18] GB/ T2975-1998, 钢及钢产品力学性能试验取样位置及试样制备[ S] . 北京: 中国标准出版社, 1998.
[19] GB/ T228-2002, 金属材料室温拉伸试验方法[ S] .北京: 中国标准出版社, 2002 .
[20] SAC(1997). Protocol for fabrication, inspection, testing and documentation of beam-column connection test and other experimental specimens. SAC Rep. SAC/ BD - 97 /02 , SAC Joint Venture, Sacramento, Calif.
{{custom_fnGroup.title_cn}}
脚注
{{custom_fn.content}}
PDF(4603 KB)
