为揭示采棉机脱棉用复杂复合结构(Complex Composed Structure, CCS)脱棉转子的振动特性,首先对CCS脱棉转子的毛刷条部分建立了计入尼龙纤维的三维微结构纤维模型。同时对毛刷条进行简化并建立了计入复合材料特性的各向异性微结构复合模型。通过改变复合模型的弹性模量比分别进行了有限元模态分析,并对比分析了纤维模型和复合模型的振动特性,获得了接近实际毛刷条模型的弹性模量比并确定了复合模型的复合材料属性。同时也对单元类型和尺寸的影响进行了对比研究,从而验证了本建模方法和数值算法的有效性。其次建立了带毛刷条和无毛刷条的CCS脱棉转子数值模型并进行了模态分析,得到其固有频率和振型。分析结果表明:毛刷条对CCS脱棉转子振动特性的影响较大,前六阶固有频率范围为52.63Hz~249.00Hz,但第一阶固有频率高于CCS脱棉转子的实际工作频率25Hz,故避免了产生共振。最后,利用转子测试平台和激光多普勒测振仪得到了脱棉转子的固有频率,该结果可以正确地反映CCS脱棉转子的振动特性,从而验证了CCS除棉转子建模方法和相关算法的有效性。这为CCS脱棉转子设计与优化提供了有效手段和参考方法。
Abstract
In order to reveal vibration characteristics of complex composite structure (CCS) de cotton rotor of a cotton picker, firstly, a 3-D microstructure fiber model including nylon fiber was established for brush strip part of CCS de cotton rotor.At the same time, the brush strip was simplified and an anisotropic microstructural composite model was established considering characteristics of composite material.Elastic modulus ratio of composite model was changed, and modal analyses were performed with finite element method.Vibration characteristics of the fiber model and the composite model were contrastively analyzed to obtain elastic modulus ratio of the model close to the actual brush strip, and determine composite material properties of composite model.At the same time, influences of element type and size were studied contrastively to verify the effectiveness of the proposed modeling method and numerical algorithm.Secondly, numerical models of CCS de cotton rotor with and without brush strip were established and modal analyses were performed to obtain the rotor natural frequencies and modal shapes.Results showed that the brush strip has a larger influence on vibration characteristics of the CCS de cotton rotor, the first six natural frequencies range is 52.63~249.00 Hz, but the rotor’s first natural frequency is higher than the rotor’s actual working frequency of 25 Hz to avoid the resonance.Finally, the rotor’s natural frequencies were obtained with a rotor test platform and Laser Doppler vibrometer.It was shown that both the numerical results and test ones agree well with each other, and can correctly reflect vibration characteristics of the CCS de cotton rotor to verify the effectiveness of the proposed modeling method and related algorithms; the results can provide a reference for design and optimization of CCS de cotton rotor.
关键词
采棉机 /
CCS脱棉转子 /
复合材料 /
模态分析 /
振动试验
{{custom_keyword}} /
Key words
cotton picker /
CCS de cotton rotor /
composite material /
modal analysis /
vibration test
{{custom_keyword}} /
{{custom_sec.title}}
{{custom_sec.title}}
{{custom_sec.content}}
参考文献
[1] 张杰,王力,赵新民.我国棉花产业的困境与出路[J].农业经济问题,2014,35(09):28-34+110.
Zhang Jie,Wang Li,Zhao Xinming,Dilemma and Outlet of Cotton Industry in China[J]. Issues in Agricultural Economy,2014,35(09):28-34+110.
[2] 毕新胜.采棉机采摘头水平摘锭工作机理的研究[D].石河子大学, 2007.
[3] 杨潇. 采棉机的研究现状及关键技术[A]. 全国各省区市机械工程学会、云南省机械工程学会.2015年第五届全国地方机械工程学会学术年会暨中国制造2025发展论坛论文集[C].全国各省区市机械工程学会、云南省机械工程学会:云南省机械工程学会,2015:5.
[4] 端景波, 张晓辉, 范国强等.棉花机械化采收技术的现状与研究[J].中国农机化学报, 2014,35(03):62-65.
Duan Jingbo,Zhang Xiaohui,Fan Guoqiang,et
al. Current situation and research on research on recovery technology of cotton machinery[J] . Journal of Chinese Agricultural Mechanization, 2014,35(03):62-65.
[5] Kepner R A, Curley R G, Brooks C R, et al. A Brush-Type Stripper for Double-Row Cotton[J]. Transactions of the ASABE,1979,22(6):1234-1237.
[6] Faircloth J C, Hutchinson R, Barnett J, et al. An evaluation of alternative cotton harvesting methods in northeast Louisiana--a comparison of the brush stripper and spindle harvester[J]. Journal of Cotton Science, 2004,8(2):55-61.
[7] John D Wanjura,Randal K Boman,Mark S Kelley,et al. Evaluation of Commercial Cotton Harvesting Systems in the Southern High Plains, Applied Engineering in Agriculture, 2013,29(3):321-332.
[8] 杨怀君,周亚立,刘向新等.刮板毛刷式采棉机采摘部件的研究[J].农机化研究,2010,32(03):49-51.
Yang Huaijun,Zhou Yali,Liu Xiangxin,et al. The Research of Picking Uniton Scraper-brush Cotton Stripper[J]. Journal of Agricultural Mechanization Research,2010,32(03):49-51.
[9] 刘向新,周亚立,杨怀君.刮板毛刷式采棉机采摘部件的有限元分析—基于Pro/E[J].农机化研究,2011,33(04):25-27+32.
Liu Xiangxin,Zhou Yali,Yang Huaijun,The Finite Element Analysis for Picking Uniton Scraper-brush Stripper Cotton— Based on Pro/E [J]. Journal of Agricultural Mechanization Research, 2010,32(03):49-51.
[10] 魏俊,王云霞,石磊等.刷辊式采棉机刷棉辊动力学分析[J].农机化研究,2016,38(06):106-109+115.
Wei Jun,Wang Yunxia,SHI Lei,et al.The Finite Element Analysis for Cotton-beated Roller of The Roller Stripping-type Cotton Harvester[J]. Journal of Agricultural Mechanization Research, 2016,38(06):106-109+115.
[11] 潘金坤,袁建宁,石磊等.刷辊式采棉机刷棉辊运动学仿真分析[J].农机化研究,2015,37(12):63 +69.
Pan Jinkun,Yuan Jianning,Shi Lei, et al. Roller Bat’s Kinematical Simulation and Analysis for Roller Stripping - type Cotton Harvester[J]. Journal of Agricultural Mechanization Research, 2015,37(12):63 +69.
[12] 黄铭森,石磊,张玉同等.刷辊式采棉机的改进设计与试验[J].农业工程学报,2017,33(20):41-47.
Huang Mingsen, Shi Lei, Zhang Yutong, et al. Revised design and experiments on brush-rolling cotton harvester[J]. Transactions of the Chinese Society of Agricultural Engineering,2017,33(20):41-47.
[13] 刘妤,徐梓翔,许洪斌,陈亚洁.基于刚柔耦合模型的微耕机振动特性分析[J].振动与冲击,2018,37(24):250-256.
Liu Yu,Xu Zixiang,Xu Hongbin,et al. Analysis of vibration characteristics for power tillers based on a rigid-flexible coupling model[J]. JOURNAL OF VIBRATION AND SHOCK,2018,37(24):250-256.
[14] 巫少龙,张元祥.基于ANSYS Workbench的高速电主轴动力学特性分析[J].组合机床与自动化加工技术,2010(09):20-22 +26.
Wu Shaolong,Zhang Yuanxiang. Based on ANSYS Workbench High Speed Electricity Spindle Dynamics Characteristic Analysis[J]. Modular Machine Tool & Automatic Manufacturing Technique,2010(09):20-22 +26.
[15] 陈完年,王天雷,王大承.基于有限元的制动蹄生产专机结构优化设计[J].机床与液压,2013,41(22):35-38.
Chen Wannian,Wang Tianlei,Wang Dacheng. Structure Optimal Design of Special Machine Tool for Brake Shoe Based on FEA[J]. Machine Tool & Hydraulics,2013,41(22):35-38.
[16] 李伟.高速在线清洗机的设计[J].轻合金加工技术,1999(05):12-15+28.
Li Wei. Design of High- Speed in Line Cleaner[J]. Light Alloy Fabrication Technology,1999(05):12-15+28.
[17] 郑磊,尹健,纪斌等.基于ANSYS的脱粒滚筒模态分析[J].农机化研究,2013,35(04):48-51.
Zheng Lei,Yinjian,Ji Bing,et al. Modaling Analysis of Threshing Cylinder Based on Ansys[J]. Journal of Agricultural Mechanization Research, 2013,35(04):48-51.
{{custom_fnGroup.title_cn}}
脚注
{{custom_fn.content}}