包含刀具-工件多重交互与速度效应的铣削颤振稳定性分析

PDF(5297 KB)

振动与冲击 ›› 2021, Vol. 40 ›› Issue (17) : 14-24.

论文

籍永建1，王西彬2，刘志兵2，王红军1

作者信息 +

Stability analysis of milling chatter with tool-workpiece multiple interactions and velocity effects

JI Yongjian1, WANG Xibin2, LIU Zhibing2, WANG Hongjun1

Author information +

文章历史 +

摘要

为研究刀具-工件多重交互与速度效应对铣削颤振稳定性的影响，建立了包含刀具-工件多重交互与速度效应的铣削动力学模型，阐明了无刀轴倾角状态下再生效应、过程阻尼、刀具结构模态耦合与速度效应的耦合作用对铣削颤振稳定性的影响规律，研究了不同径向浸入比下刀具-工件交互与速度效应对铣削稳定性的影响。结果表明，与只考虑再生效应的铣削动力学模型相比，当同时考虑再生效应、过程阻尼与刀具结构模态耦合时，得到的稳定性叶瓣图中颤振区域发生明显变化；当主轴转速较低时，刀具-工件之间的多重交互效应是影响铣削颤振稳定性的主要因素，速度效应对极限切深的影响可忽略不计；随着主轴转速升高，速度效应对极限切深的影响逐渐增大，稳定性叶瓣图中稳定区域呈逐渐减小趋势；在一定范围内，随着铣刀后刀面磨损带的增加，铣削极限切深逐渐增大；主轴转速一定时，径向浸入比相对较小的情况下过程阻尼对铣削稳定性的影响更加明显。采用铣削试验进行验证，结果表明，与传统动力学模型相比，构建的铣削动力学模型能够更加可靠地预测实际铣削状态。

Abstract

Here, to study effects of tool-workpiece multiple interactions and velocity effect on milling chatter stability, a milling dynamic model including tool-workpiece multiple interactions and velocity effect was established.Influence laws of regeneration effect, process damping, tool structure modal coupling and velocity effect on milling chatter stability under the condition of no tool axis inclination angle were clarified, and effects of tool-workpiece interaction and velocity effect on milling stability under different radial immersion ratios were studied.The results showed that compared with the milling dynamic model only considering regenerative effect, chatter region in stability lobe diagram changes obviously when simultaneously considering regenerative effect, process damping and tool structure modal coupling; when the spindle’s rotating speed is lower, tool-workpiece multiple interaction effects are the main factor affecting milling chatter stability, influence of speed effect on limit cutting depth can be negligible; with increase in spindle rotating speed, influence of speed effect on limit cutting depth gradually increases, and stable region in stability lobe diagram gradually decreases; within a certain range, with increase in wear land of milling cutter flank, milling limit cutting depth gradually increases; when spindle speed is constant, process damping affects milling stability more obviously under the condition of relatively smaller radial immersion ratio; compared with traditional dynamic model, the established milling dynamic model here can more reliably predict actual milling state.

导出引用

籍永建，王西彬，刘志兵，王红军. 包含刀具-工件多重交互与速度效应的铣削颤振稳定性分析[J]. 振动与冲击, 2021, 40(17): 14-24

JI Yongjian, WANG Xibin, LIU Zhibing, WANG Hongjun. Stability analysis of milling chatter with tool-workpiece multiple interactions and velocity effects[J]. Journal of Vibration and Shock, 2021, 40(17): 14-24

参考文献

［1］YUE Caixu, GAO Haining, LIU Xianli, et al.A review of chatter vibration research in milling ［J］.Chinese Journal of Aeronautics, 2019, 32(2): 215-242.
［2］ZHU Lida, LIU Changfu.Recent progress of chatter prediction, detection and suppression in milling ［J］.Mechanical Systems and Signal Processing, 2020, 143: 1-37.
［3］王跃辉, 王民.金属切削过程颤振控制技术的研究进展［J］.机械工程学报, 2010, 46(7): 166-174.
WANG Yuehui, WANG Min.Advances on machining chatter suppression research ［J］.Journal of Mechanical Engineering, 2010, 46(7): 166-174.
［4］ALTINTAS Y, BUDAK E.Analytical prediction of stability lobes in milling ［J］.CIRP Annals-Manufacturing Technology, 1995, 44(1): 357-362.
［5］AHMADI K, ISMAIL F.Stability lobes in milling including process damping and utilizing multi-frequency and semi-discretization methods ［J］.International Journal of Machine Tools & Manufacture, 2012, 54/55: 46-54.
［6］ZHANG Xiaojian, XIONG Caihua, DING Ye, et al.Milling stability analysis with simultaneously considering the structural mode coupling effect and regenerative effect ［J］.International Journal of Machine Tools & Manufacture, 2012, 53(1): 127-140.
［7］HAJDU D, BORGIOLI F, MICHIELS W, et al.Robust stability of milling operations based on pseudospectral approach ［J］.International Journal of Machine Tools and Manufacture, 2020, 149: 1-10.
［8］智红英, 闫献国, 杜娟, 等.预测铣削稳定性的Hamming线性多步法［J］.振动与冲击, 2018, 37(22): 67-74.
ZHI Hongying, YAN Xianguo, DU Juan, et al.Prediction of the milling stability based on the Hamming linear multistep method ［J］.Journal of Vibration and Shock, 2018, 37(22): 67-74.
［9］智红英, 闫献国, 杜娟, 等.预测铣削稳定性的隐式Adams方法［J］.机械工程学报, 2018, 54(23): 223-232.
ZHI Hongying, YAN Xianguo, DU Juan, et al.Prediction of the milling stability based on the implicit Adams method ［J］.Journal of Mechanical Engineering, 2018, 54(23): 223-232.
［10］GURDAL O, OZTURK E, SIMS N D.Analysis of process damping in milling ［J］.Procedia CIRP, 2016, 55: 152-157.
［11］WANG D Q, LSER M, IHLENFELDT S, et al.Milling stability analysis with considering process damping and mode shapes of in-process thin-walled workpiece ［J］.International Journal of Mechanical Sciences, 2019, 159: 382-397.
［12］WU D W.A new approach of formulating the transfer function for dynamic cutting process ［J］.Journal of Engineering for Industry Transactions of the ASME, 1989, 111(1): 37-47.
［13］李欣, 李亮, 何宁.过程阻尼对铣削系统稳定性的影响［J］.振动与冲击, 2014, 33(9): 16-20.
LI Xin, LI Liang, HE Ning.Influence of process damping on a milling system’s stability ［J］.Journal of Vibration and Shock, 2014, 33(9): 16-20.
［14］FENG Jia, WAN Min, GAO Tingqi, et al.Mechanism of process damping in milling of thin-walled workpiece ［J］.International Journal of Machine Tools & Manufacture, 2018, 134: 1-19.
［15］TANG Xiaowei, PENG Fangyu, YAN Rong, et al.An effective time domain model for milling stability prediction simultaneously considering multiple modes and cross-frequency response function effect ［J］.The International Journal of Advanced Manufacturing Technology, 2016, 86(1/2/3/4): 1037-1054.
［16］任勇生, 马伯乐, 马静敏.考虑刀杆结构非线性的铣削过程颤振稳定性与主共振［J］.振动与冲击, 2019, 38(23): 62-69.
REN Yongsheng, MA Bole, MA Jingmin.Flutter stability and main resonance of a milling system considering structural nonlinearity of cutter bar ［J］.Journal of Vibration and Shock, 2019, 38(23): 62-69.
［17］LI Zhongyun, JIANG Shanglei, SUN Yuwen.Chatter stability and surface location error predictions in milling with mode coupling and process damping ［J］.Proceedings of the Institution of Mechanical Engineers, Part B: Journal of Engineering Manufacture, 2019, 233(3): 686-698.
［18］JI Yongjian, WANG Xibin, LIU Zhibing, et al.Milling stability prediction with simultaneously considering the multiple factors coupling effects-regenerative effect, mode coupling, and process damping ［J］.The International Journal of Advanced Manufacturing Technology, 2018, 97(5/6/7/8): 2509-2527.
［19］秦国华, 娄维达, 吴竹溪, 等.基于过程阻尼和结构模态耦合的铣削稳定性分析与试验验证［J］.中国科学: 技术科学, 2020,50(9): 1-15.
QIN Guohua, LOU Weida, WU Zhuxi, et al.Milling stability analysis and validation based on the coupling of process damping and structural mode ［J］.Scientia Sinica Technologica, 2020,50(9): 1-15.
［20］单文桃, 陈小安, 王洪昌, 等.高速电主轴铣削稳定性研究［J］.振动与冲击, 2017, 36(19): 242-249.
SHAN Wentao, CHEN Xiao’an, WANG Hongchang, et al.Milling stability of high speed motorized spindles ［J］.Journal of Vibration and Shock, 2017, 36(19): 242-249.［21］CAO Y Z, ALTINTAS Y.A general method for the modeling of spindle-bearing systems ［J］.Journal of Mechanical Design, 2004, 126(6): 1089-1104.
［22］JONES A B.A general theory for elastically constrained ball and radial roller bearings under arbitrary load and speed conditions ［J］.Journal of Basic Engineering, 1960,82(2): 309-320.
［23］CAO Hongrui, LI Bing, HE Zhengjia.Chatter stability of milling with speed-varying dynamics of spindles ［J］.International Journal of Machine Tools & Manufacture, 2012, 52(1): 50-58.
［24］MERDOL S D, ALTINTAS Y.Multi frequency solution of chatter stability for low immersion milling ［J］.Journal of Manufacturing Science and Engineering—Transactions of the ASME, 2004, 126(3): 459-466.
［25］AHMADI K.Analytical investigation of machining chatter by considering the nonlinearity of process damping ［J］.Journal of Sound and Vibration, 2017, 393: 252-264.
［26］HU Teng, YIN Guofu, SUN Mingnan.Model based research of dynamic performance of shaft-bearing system in high-speed field ［J］.Shock and Vibration, 2014, 2014: 1-12.
［27］籍永建.主轴系统-刀具-工件交互效应下的铣削稳定性分析与试验研究［D］.北京: 北京理工大学, 2019.
［28］JI Yongjian, WANG Xibin, LIU Zhibing, et al.Five-axis flank milling stability prediction by considering the tool-workpiece interactions and speed effect ［J］.The International Journal of Advanced Manufacturing Technology, 2020, 108(7/8): 2037-2060.
［29］LU Yao’an, DING Ye, ZHU Limin.Dynamics and stability prediction of five-axis flat-end milling ［J］.Journal of Manufacturing Science and Engineering, 2017, 139(6): 1-11.
［30］WANG Minghai, GAO Lei, ZHENG Yaohui.An examination of the fundamental mechanics of cutting force coefficients ［J］.International Journal of Machine Tools and Manufacture, 2014, 78: 1-7.