不同振动方式下的钛合金超声振动铣削表面完整性研究

PDF(1960 KB)

振动与冲击 ›› 2021, Vol. 40 ›› Issue (4) : 164-170.

论文

武民1,2 ，马利杰2，王占奎2，苏建修2

作者信息 +

Influence of vibration modes on surface integrity during ultrasonic vibration milling of titanium alloy

WU Min1,2,MA Lijie2,WANG Zhankui2,SU Jianxiu2

Author information +

文章历史 +

摘要

钛合金在机械工程领域应用广泛，其加工表面完整性对钛合金工件的耐磨性、疲劳强度、使用寿命有着非常重要的影响。本文通过对工件施加不同振动方向的超声振动，开展了不同振动方向下的TC4钛合金超声振动侧铣平面试验，分析了不同振动方式的运动学轨迹特征，研究了振动方式、切削参数对钛合金加工表面完整性的影响规律。结果表明：法向振动铣削后的表面形貌变形程度、表面粗糙度均大于切向振动和轴向振动；随振幅的增大，法向振动铣削和切向振动铣削表面粗糙度呈上升趋势，轴向振动铣削呈下降趋势；法向振动铣削的表面显微硬度大于轴向振动铣削与切向振动铣削，当振幅大于3.5μm时随着振幅的增加三者都呈现出减小的趋势。法向振动铣削的表面残余应力均大于轴向振动铣削和切向振动铣削，振幅为3.5μm时的残余应力均大于振幅为5.4μm时的残余应力。与普通铣削相比，超声振动铣削能够提高加工表面的显微硬度和残余压应力，对于改善工件的耐磨性和抗疲劳性具有重要的作用。

Abstract

Titanium alloys are widely used in the field of mechanical engineering, and their machined surface integrity plays an important role in the wear resistance, fatigue strength and service life of titanium alloy workpieces.In this paper, ultrasonic vibration side milling experiments of TC4 titanium alloy in different vibration directions were carried out by applying ultrasonic vibration to the titanium alloy workpieces.The kinematic characteristics of different vibration modes were analyzed, and the influence of cutting parameters and vibration modes on the surface integrity of titanium alloy was studied.The results show that the surface morphology deformation degree and surface roughness of normal vibration milling were greater than tangential vibration and axial vibration.The surface roughness of normal vibration milling and tangential vibration milling shows an upward trend, while that of axial vibration milling shows a downward trend with the increase of amplitude.The surface microhardness of normal vibration milling is greater than that of tangential vibration milling.Both axial and tangential vibration milling show a decreasing trend with the increase of the amplitude when the amplitude is larger than 3.5 μm.Surface residual stress in normal vibration milling is greater than that in axial vibration milling and tangential vibration milling, and residual stress in amplitude of 3.5 μm is greater than that in the amplitude of 5.4 μm.Compared with common milling, ultrasonic vibration milling can improve the microhardness and residual compressive stress of the machined surface, which plays an important role in improving the wear resistance and fatigue resistance of the workpieces.

导出引用

武民1,2,马利杰2，王占奎2，苏建修2. 不同振动方式下的钛合金超声振动铣削表面完整性研究[J]. 振动与冲击, 2021, 40(4): 164-170

WU Min1,2,MA Lijie2,WANG Zhankui2,SU Jianxiu2 . Influence of vibration modes on surface integrity during ultrasonic vibration milling of titanium alloy[J]. Journal of Vibration and Shock, 2021, 40(4): 164-170

参考文献

[1] SU H, LIU P, FU Y, et al. Tool life and surface intergrity in high-speed milling of titanium alloy TA15 with PCD/PCBN tools [J]. Chinese Journal of Aeronautics, 2012, 25(5):784-790.
[2] YANGD D,LIU Z. Surface Topography Analysis and Cutting Parameters Optimization for Peripheral Milling of Titanium Alloy Ti-6Al-4V [J]. International Journal of Refractory Metals & Hard Materials, 2015, 51:192-200.
[3] KULKARNI M, PATILSEN L, JUNKAR I, et al. Wettability Studies of Topologically Distinct Titanium Surfaces [J]. Colloids & Surfaces B Biointerfaces, 2015, 129:47-53.
[4] Rahim E A, Sasahara H. A study of the effect of palm oil as MQL lubricant on high speed drilling of titanium alloys [J]. Tribology International, 2011, 44( 3) :309-317.
[5] 杨振朝，张定华，姚倡锋. TC4钛合金高速铣削参数对表面完整性的影响研究[J], 西北工业大学学报, 2009, 27:538-543.
YANG Zhen-chao, ZHANG Ding-hua, YAO Chang-feng. Effect of TC4 titanium alloy high speed milling parameters on surface integrity [J]. Journal of Northwestern Polytechnical University, 2009, 27:538-543.
[6] 谭靓，张定华，姚倡锋，等. 刀具几何参数对钛合金铣削力和表面完整性的影响[J]. 中国机械工程, 2015, 26(06):737-742.
TAN Liang, ZHANG Ding-hua, YAO Chang-feng, et al. Influence of Tool Geometrical Parameters on Milling Force and Surface Integrity in Milling Titanium Alloy [J]. China Mechanical Engineering, 2015, 26(06):737-742.
[7] Shi Q, Yang Y F, He N, et al. Experiment Study of Tool Wear and Surface Integrity in High Speed Milling of a New Damage-Tolerant Titanium Alloy [J]. Materials Science Forum, 2012, 723(13):177-181.
[8] Fang Y F, Tee K F. Effects on Surface Integrity of Ti6Al4V in High Speed Milling [J]. Key Engineering Materials, 2017, 737:156-161.
[9] 赵波，赵斌斌，范凯洋，等. 垂直平面内二维超声振动铣削系统稳定性研究[J]. 振动测试与诊断, 2017, 37(03) 617-621+636.
ZHAO Bo, ZHAO Bin-bin, FAN Kai-yang, et al. Study on the stability of Two Dimensional Ultrasonic Vibration Milling System in Vertical Plane [J]. Journal of Vibration, Measurement & Diagnosis, 2017, 37(03) 617-621+636.
[10] ZHANG Y, ZHAO B, WANG Y, et al. Effect of machining parameters on the stability of separated and unseparated ultrasonic vibration of feed direction assisted milling [J]. Journal of Mechanical Science & Technology, 2017, 31:851-858.
[11] 童景琳，卫官. 超声椭圆振动切削钛合金切削力特性研究[J]. 振动与冲击, 2019, 38(09):208-215.
TONG Jing-lin, WEI Guan. Characteristics of cutting force during titanium alloy processed with UEVC [J]. Journal of Vibration and Shock, 2019, 38(09):208-215.
[12] Abootorabi Zarchi M M, Razfar M R, Abdullah A. Influence of ultrasonic vibrations on side milling of AISI 420 stainless steel [J]. International Journal of Advanced Manufacturing Technology, 2013, 66:83-89.
[13] LI K M, WANG S L. Effect of tool wear in ultrasonic vibration-assisted micro-milling [J]. Proceedings of the Institution of Mechanical Engineers, Part B: Journal of Engineering Manufacture, 2014, 228(6):847-55.
[14] 唐军，赵波. 单激励纵扭复合超声振动铣削系统研究[J]. 振动与冲击, 2015, 34(06):57-61+71.
TANG Jun, ZHAO Bo. A new longitudinal-torsional composite milling system with a single excitation [J]. Journal of Vibration and Shock, 2015, 34(06):57-61+71.
[15] 刘佳佳，姜兴刚，高泽，等. 高速旋转超声椭圆振动侧铣削振幅对钛合金表面完整性影响的研究[J]. 机械工程学报, 2019, 55(11):215-223.
LIU Jia-jia, JIANG Xing-gang, GAO Ze, et al. Investigation of the Effect of Vibration Amplitude on the Surface Integrity in High-speed Rotary Ultrasonic Elliptical Machining for Side Milling of Ti-6Al-4V [J]. Journal of Mechanical Engineering, 2019, 55(11):215-223.
[16] Liu J, Jiang X, Han X, et al. Effects of rotary ultrasonic elliptical machining for side milling on the surface integrity of Ti-6Al-4V [J]. The International Journal of Advanced Manufacturing Technology, 2018(5–8):1-15.
[17] Zhang X, Kan Z, Liao W, et al. Investigation on Surface Integrity for Ultrasonic Vibration Assisted Milling Titanium Alloy [J]. Tool Engineering, 2017.
[18] 喻宏庆，高延峰，王顺钦. 钛合金径向超声振动铣削表面粗糙度研究[J]. 航空制造技术, 2016(04):58-62.
YU Hong-qing, GAO Yan-feng, WANG Shun-qin. Study on Surface Roughness of Titanium Alloy Under Radial Ultrasonic Vibration Milling [J]. Aeronautical Manufacturing Technology, 2016(04):58-62.
[19] 马超，张建华，陶国灿. 超声振动辅助铣削加工钛合金表面摩擦磨损性能研究[J]. 表面技术, 2017, 46(08):115-119.
MA Chao, ZHANG Jian-hua, TAO Guo-can. Wear and Friction Properties of Titanium Alloy Surface Subject to Ultrasonic Vibration Assisted Milling [J]. Surface Technology, 2017, 46(08):115-119.
[20] 杨晓勇. 钛合金铣削刀具磨损及表面完整性研究[D]. 天津：天津大学, 2013.
YANG Xiao-yong. Tool wear and surface integrity of titanium alloy milling [J]. Tianjin：Tianjin University, 2013.