不同剪切变形下橡胶隔震支座竖向压缩刚度试验研究

PDF(1346 KB)

振动与冲击 ›› 2021, Vol. 40 ›› Issue (6) : 93-99.

论文

金建敏1，肖骥1，刘彦辉1，冯德民2，谭平1，黄襄云1

作者信息 +

Experimental study on the vertical compressive stiffness of rubber isolation bearings under different shear deformation

JIN Jianmin1，XIAO Ji1，LIU Yanhui1，FENG Demin2，TAN Ping1，HUANG Xiangyun1

Author information +

文章历史 +

摘要

针对橡胶隔震支座，研究了其在不同水平剪切变形状态下的竖向压缩刚度理论计算方法，基于双弹簧模型，提出了改进的不同剪切变形状态下橡胶隔震支座竖向压缩刚度理论计算公式。采用建筑结构中常用的第二形状系数S2=5系列(G4)天然橡胶支座及铅芯橡胶支座，进行了不同压应力及不同剪切变形下的压缩性能试验，通过试验研究不同水平剪切变形状态下的橡胶隔震支座竖向压缩刚度。研究结果表明：橡胶隔震支座竖向压缩刚度随剪应变增大而减小，随设计压应力增大而增大；在设计压应力相同的条件下，橡胶隔震支座竖向压缩刚度随压应力变化范围的增大而减小；基于橡胶隔震支座有效承载面积的公式虽能反映支座竖向压缩刚度随剪应变增大而减小这一趋势，但与试验结果相比误差较大；既有的基于双弹簧模型的竖向压缩刚度计算公式计算精度优于基于有效承载面积的竖向压缩刚度计算公式，但在150%以上剪应变时，也存在误差较大的问题；提出的改进的基于双弹簧模型的不同剪切变形状态下橡胶隔震支座竖向压缩刚度计算公式与试验结果吻合较好，与既有基于有效承载面积计算橡胶隔震支座竖向压缩刚度和基于双弹簧模型的计算橡胶隔震支座竖向压缩刚度的公式相比较，具有较高的计算精确度。

Abstract

For rubber isolation bearings in isolated structures, the theoretical calculation methods for its vertical compression stiffness under different horizontal shear deformation were studied, and based on a two-spring model, an improved theoretical calculation formula for the stiffness was presented.Compressive property tests under different compressive stress and different shear deformation for linear natural rubber bearings and lead rubber bearings of S2=5 series (G4) commonly used in building structures were carried out and the vertical compression stiffness of rubber isolation bearings under different horizontal shear deformation was investigated by experiments.The results show that the vertical compressive stiffness of the bearing decreases with the increase of shear strain and increases with the increase of design compressive stress.Under the condition of the same design compressive stress, it decreases with the increase of the changing range of compressive stress.Although the calculation based on the effective bearing area of the bearing can reflect the trend that the vertical compression stiffness of the bearing decreases with the increase of shear strain, there is a big error between the calculation and test results.The calculation method based on the two-spring model has better calculation accuracy compared with that based on the effective bearing area of the bearing, however, there is also a big error when the shear strain is not less than 150%.The improved calculation formula for the vertical compression stiffness of rubber isolation bearings under different horizontal shear deformation presented in the paper can get the results in good agreement with the experimental results and has better calculation accuracy compared with conventional calculation methods based on the double-spring model and based on the effective bearing area of the bearing.

导出引用

金建敏1，肖骥1，刘彦辉1，冯德民2，谭平1，黄襄云1. 不同剪切变形下橡胶隔震支座竖向压缩刚度试验研究[J]. 振动与冲击, 2021, 40(6): 93-99

JIN Jianmin1，XIAO Ji1，LIU Yanhui1，FENG Demin2，TAN Ping1，HUANG Xiangyun1. Experimental study on the vertical compressive stiffness of rubber isolation bearings under different shear deformation[J]. Journal of Vibration and Shock, 2021, 40(6): 93-99

参考文献

［1］RYAN K L,KELLY J M, CHOPRA A K.Experimental observation of axial-load effects in isolation bearings［C］//13th World Conference on Earthquake Engineering.Vancouver: Canadian Association for Earthquake Engineering, 2004.
［2］WARN G P, WHITTAKER A S, CONSTANTINOU M C.Vertical stiffness of elastomeric and lead-rubber seismic isolation bearings ［J］.Journal of Structural Engineering, 2007,133(9):1227-1236.
［3］刘文光.橡胶隔震支座力学性能及隔震结构地震反应分析研究［D］.北京：北京工业大学，2003.
［4］王建强，赵云，刘耀东，等.铅芯橡胶支座竖向压缩刚度试验研究［J］.铁道建筑,2015(11):33-36.
WANG Jianqiang, ZHAO Yun, LIU Yaodong,et al.Experimental study on vertical stiffness of lead-centered rubber bearings［J］.Railway Engineering, 2015(11): 33-36.
［5］王建强，魏明明，李政，等.高阻尼橡胶支座竖向压缩刚度试验研究［J］.建筑科学，2016，32(3):46-49.
WANG Jianqiang, WEI Mingming, LI Zheng,et al.Experimental study on vertical stiffness of high damping rubber bearings［J］.Building Science, 2016, 32(3): 46-49.
［6］王维，李爱群，韩凤萍，等.低硬度G3橡胶隔震支座试验研究及其隔震效果分析［J］.工程抗震与加固改造，2019，41(1):48-55.
WANG Wei, LI Aiqun, HAN Fengping, et al.Experiment research and isolation effect analysis on low-hardness G3 rubber bearings［J］.Earthquake Resistant Engineering and Retrofitting，2019, 41(1):48-55.
［7］日本建筑学会.隔震结构设计［M］.刘文光, 译.北京：地震出版社，2006.
［8］KOH C G, KELLY J M.A simple mechanical model for elastomeric bearings used in base isolation［J］.International Journal of Mechanical Sciences, 1988, 30 (12):933-943.
［9］KELLY J M.Earthquake-resistant design with rubber［M］.London: Springer, 1997.
［10］RYAN K L, KELLY J M, CHOPRA A K.Nonlinear model for lead-rubber bearings including axial-load effects［J］.Journal of Engineering Mechanics, 2005,131(12): 1270-1278.
［11］KUMAR M, WHITTAKER A S, CONSTANTINOU M C.An advanced numerical model of elastomeric seismic isolation bearings［J］.Earthquake Engineering and Structural Dynamics,2014,43(13): 1955-1974.
［12］KUMAR M, WHITTAKER A S, CONSTANTINOU M C.Response of base-isolated nuclear structures to extreme earthquake shaking［J］.Nuclear Engineering and Design,2015,295: 860-874.
［13］周福霖.工程结构减震控制［M］.北京：地震出版社，1997.
［14］橡胶支座-第1部分：隔震橡胶支座试验方法:GB/T 20688.1—2007［S］.北京：中国标准出版社，2007.
［15］建筑抗震设计规范:GB 50011—2010［S］ .北京: 中国建筑工业出版社，2010.