基于离散元法的镶齿冲击与切削破岩效果数值分析研究

PDF(3598 KB)

振动与冲击 ›› 2022, Vol. 41 ›› Issue (22) : 173-183.

论文

邹久群1,2，张金松2，庞建勇2

作者信息 +

Numerical analysis on the rock-breaking effect of impacting and cutting actions of inserted tooth cutters based on the discrete element method

ZOU Jiuqun1,2,ZHANG Jinsong2,PANG Jianyong2

Author information +

文章历史 +

摘要

随着深地资源的开发，镶齿滚刀在硬岩破碎竖向钻进中的应用愈加广泛。基于高精度拟合的离散元数值模型研究各因素对破岩效果的影响，获得动荷载波动差异系数和比能耗的变化规律。研究发现镶齿破岩以拉伸破坏裂纹为主，齿端曲率是影响微裂纹数量的最关键因素，微裂纹的方位角分布显示，受拉裂纹的分布较均匀，而剪切裂纹的分布主要集中在45°和135°附近。对于不同破岩模式下，镶齿破岩参数与荷载波动情况及比能耗的相关性差异较大，锥角和齿端曲率的影响存在极值，而侵深和攻角表现出单调的相关性。初始压力条件开始对破岩效率有抑制作用，而在与单轴抗压强度比值达到0.8时，比能耗明显下降。随着初始压力系数的增大，微剪切裂纹方位角分布逐渐均布化，而微拉伸裂纹逐渐向水平方向聚集。
关键词：硬岩破碎；镶齿破岩；离散元；平节理接触模型；数值模拟

Abstract

With the development of deep ground resources, inserted-tooth hob is widely used in vertical drilling of hard-rock fragmentation. Based on the high precision fitting discrete element numerical model, the influences of various factors on rock breaking efficiency were studied, and the variation rules of load fluctuation difference coefficient and specific energy consumption were obtained. The results show that tensile crack is the main failure pattern of inserted-tooth cutter, and tooth tip curvature is the most significant factor affecting the number of microcracks. The distribution of azimuth angle of microcracks shows that the distribution of tensile crack is uniform, while the distribution of shear crack is mainly concentrated near 45° and 135°. For different rock breaking modes, the correlation between rock breaking parameters and load fluctuation or specific energy consumption is different, the influence of cone angle and tooth tip curvature has extreme value, while the penetration depth and attack angle show monotonous correlation. The initial pressure condition inhibited the rock breaking efficiency, but when the ratio to uniaxial compressive strength reached 0.8, the energy consumption decreased significantly. With the increase of the initial pressure coefficient, the azimuth distribution of micro-shear cracks gradually homogenizes, while the micro-tensile cracks gradually converge horizontally.
Keywords：Hard-rock fragmentation; inserted tooth cutter; discrete element method; flat-joint contact model; numerical modeling

导出引用

邹久群1,2，张金松2，庞建勇2. 基于离散元法的镶齿冲击与切削破岩效果数值分析研究[J]. 振动与冲击, 2022, 41(22): 173-183

ZOU Jiuqun1,2,ZHANG Jinsong2,PANG Jianyong2. Numerical analysis on the rock-breaking effect of impacting and cutting actions of inserted tooth cutters based on the discrete element method[J]. Journal of Vibration and Shock, 2022, 41(22): 173-183

参考文献

[1] 张永成. 钻井施工手册[M]. 北京: 煤炭工业出版社, 2010.
Zhang Yongcheng. Handbook of Mine Shaft Drilling[M]. Beijing: China Coal Industry Publishing House, 2010.
[2] 谭青, 张魁, 周子龙. 球齿滚刀作用下岩石裂纹的数值模拟与试验观测[J]. 岩石力学与工程学报, 2010, 29(01):163-169.
Tan Qing, Zhang Kui, Zhou Zilong. Numerical simulation and experimental observation of rock cracks under action of spherical tooth hob cutter[J]. Chinese Journal of Rock Mechanics and Engineering, 2010, 29(01):163-169.
[3] 胡修坤. 反井钻机镶齿滚刀破岩机理及性能研究[博士论文D]. 中国矿业大学, 2019.
Hu Xiukun. Research on Rock Breaking Mechanism and Performance of Tipped Hob for Raise Boring Machine [Doctoral dissertation]. China University of Mining and Technology, 2019.
[4] Park J, Kang H, Lee J, Kim J, Oh J, Cho J, Rostami J, Kim H D. A study on rock cutting efficiency and structural stability of a point attack pick cutter by lab-scale linear cutting machine testing and finite element analysis[J]. International journal of rock mechanics and mining sciences, 2018, 103:215-229.
[5] Li X F, Li H B, Liu Y Q, Zhou Q C, Xia X. Numerical simulation of rock fragmentation mechanisms subject to wedge penetration for TBMs[J]. Tunnelling and underground space technology, 2016, 53:96-108.
[6] Hurt K G. Rock cutting experiments with point attack tools[J]. International Journal of Rock Mechanics and Mining Sciences, 1980, 17(6): A124.
[7] 汪莹莹. 不同齿形的镶齿滚刀破岩效果模拟仿真[硕士论文D]. 合肥工业大学, 2017.
Wang Yingying. Numerical Analysis on Rock Breaking Effect with Different Inserted Tooth Rolling Cutters, [Master's dissertation]. Hefei University of Technology, 2017.
[8] 吴帆, 殷丽君, 张浩. 镶齿滚刀破岩机理及效率的旋转破岩试验[J]. 中国公路学报, 2018, 31(10):150-159.
Wu Fan, Yin Lijun, Zhang Hao. Rock fragmentation mechanism and efficiency under inserted-tooth roller cutter by rotary cutting test[J]. China Journal of Highway and Transport, 2018, 31(10):150-159.
[9] 祝效华, 郭光亮. 动静载荷比对钻齿破岩效率的影响研究[J]. 振动与冲击, 2019, 38(01):22-28.
Zhu Xiaohua, Guo Guangliang. Effects of ratio of dynamic load to static one on rock-breaking efficiency[J]. Journal of Vibration and Shock, 2019, 38(01):22-28.
[10] Li X B, Wang S F, Wang S Y. Experimental Investigation of the Influence of Confining Stress on Hard Rock Fragmentation Using a Conical Pick[J]. Rock mechanics and rock engineering, 2018, 51(1):255-277.
[11] Wang S F, Li X B, Du K, Wang S Y. Experimental investigation of hard rock fragmentation using a conical pick on true triaxial test apparatus[J]. Tunnelling and underground space technology, 2018, 79:210-223.
[12] 龚秋明. 掘进机隧道掘进概论[M]. 北京: 科学出版社, 2014.
Gong Qiuming. Introduction to tunneling by tunneling machine[M]. Beijign: science press, 2014.
[13] Yin L J, Gong Q M, Ma H S, Zhao J, Zhao X B. Use of indentation tests to study the influence of confining stress on rock fragmentation by a TBM cutter[J]. International journal of rock mechanics and mining sciences, 2014, 72: 261-276.
[14] Pan Y C, Liu Q S, Liu J P, Liu Q, Kong X X. Full-scale linear cutting tests in Chongqing Sandstone to study the influence of confining stress on rock cutting efficiency by TBM disc cutter[J]. Tunnelling and underground space technology, 2018, 80:197-210.
[15] 米建宇, 黄飞, 李树清, 王荣荣, 李丹. 基于SPH-FEM耦合算法的后混合磨料水射流冲击破岩数值模拟研究[J].振动与冲击, 2021, 40(16):132-139.
Mi Jianyu, Huang Fei, Li Shuqing, Wang Rongrong, Li Dan. Numerical simulation of rock breaking by rear-mixed abrasive water jet based on an SPH-FEM coupling algorithm[J]. Journal of Vibration and Shock, 2021, 40(16):132-139.
[16] 刘书斌, 倪红坚, 王勇, 张恒. 多维冲击提高PDC钻头破岩效率的机理研究[J]. 振动与冲击, 2021, 40(02):258-264+278.
Liu Shubing, Ni Hongjian, Wang Yong, Zhang Hong. Mechanism of multi-dimensional impact loads applied in increasing the rock cutting efficiency of a PDC bit[J]. Journal of Vibration and Shock, 2021, 40(02):258-264+278.
[17] 张魁, 夏毅敏, 谭青. 不同围压条件下TBM刀具破岩模式的数值研究[J]. 岩土工程学报, 2010, 32(11):1780-1787.
Zhang Kui, Xia Yimin, Tan Qing. Numerical study on modes of breaking rock by TBM cutter under different confining pressures[J]. Chinese Journal of Geotechnical engineering, 2010, 32(11): 1780-1787.
[18] 莫振泽, 李海波, 周青春. 基于UDEC的隧道掘进机滚刀破岩数值模拟研究[J]. 岩土力学, 2012, 33(04):1196-1202.
Mo Zhenze, Li Haibo, Zhouo Qingchun. Research on numerical simulation of rock breaking using TBM disc cutters based on UDEC method[J]. Rock and Soil Mechanics, 2012, 33(04):1196-1202.
[19] Gong Q M, Jiao Y Y, Zhao J. Numerical modelling of the effects of joint spacing on rock fragmentation by TBM cutters[J]. Tunnelling and Underground Space Technology, 2005, 21(1): 46-55.
[20] Rojek J, Oñate E, Labra C, Kargl H. Discrete element simulation of rock cutting[J]. International journal of rock mechanics and mining sciences, 2011, 48(6): 996-1010.
[21] Li X F, Wang S B W, Ge S R, Malekian R, Li Z X. Investigation on the influence mechanism of rock brittleness on rock fragmentation and cutting performance by discrete element method[J]. Measurement, 2018, 113:120-130.
[22] Zou J Q, Yang W H, Han J H. Discrete Element Modeling of the Effects of Cutting Parameters and Rock Properties on Rock Fragmentation[J]. IEEE access, 2020, 2020(8):136393-136408.
[23] Zou J Q, Han J H, Zhang T, Yang W H. Experimental Investigation and Numerical Analyses for Red Sandstone Rock Fragmentation[J]. International Journal of Geomechanics, 2020, 20(12): 1-13.
[24] 翟淑芳. 深部复杂地层的TBM滚刀破岩机理研究[博士论文D]. 重庆大学, 2017.
Cui Shufang. Rock Fragmentation by TBM Cutters in Deep Complicated Formation [Doctoral dissertation]. Chongqing University, 2017.
[25] 何树江. 基于颗粒流的灰岩细观力学参数标定方法及其敏感性分析[硕士论文D]. 济南: 山东大学, 2019.
He Shujiang. Calibration Method and Sensitivity Analysis of Micromechanics Parameters for Limestone Based on Particle Flow [Master's dissertation]. Jinan: Shandong University, 2019.
[26] 冀佩琦，张晓平，张旗. 延脆性变化对隧道掘进机刀具破岩过程及其破坏模式影响的颗粒元模拟分析[J]. 岩土力学, 2016, 37(S2):724-734.
Ji Peiqi, Zhang Xiaoping, Zhang Qi. Particle flow code analysis of effect of ductility-brittleness change on TBM cutters rock fragmentation process and its failure mode[J]. Rock and Soil Mechanics, 2016, 37(S2):724-734.
[27] Group I C. PFC2d User’s Manual (Version 3.1) [M]. Minnesota: Itasca Consulting Group, 2004.
[28] Bilgin N, Demircin M A, Copur H, Balci C, Tuncdemir H, Akcin N. Dominant rock properties affecting the performance of conical picks and the comparison of some experimental and theoretical results[J]. International journal of rock mechanics and mining sciences, 2006, 43(1):139-156.
[29] 邓建明. 反井钻机镶齿滚刀破岩机理及扩孔钻进参数研究[硕士论文D]. 煤炭科学研究总院, 2020.
Deng Jianming. Research on Rock Breaking Mechanism and Reaming Drilling Parameters of Raise Boring Machine [Master's dissertation]. China Coal Research Institute, 2020.