采用拉索模数伸缩缝的斜交桥减隔震参数优化

张鹏辉,冯睿为,郭军军,袁万城

振动与冲击 ›› 2022, Vol. 41 ›› Issue (9) : 120-127.

PDF(2467 KB)
PDF(2467 KB)
振动与冲击 ›› 2022, Vol. 41 ›› Issue (9) : 120-127.
论文

采用拉索模数伸缩缝的斜交桥减隔震参数优化

  • 张鹏辉,冯睿为,郭军军,袁万城
作者信息 +

Optimization of seismic mitigation and isolation parameters of skew bridge with cable modulus expansion joint

  • ZHANG Penghui, FENG Ruiwei, GUO Junjun, YUAN Wancheng
Author information +
文章历史 +

摘要

为了解决减隔震参数优化过程中参数个数增加后计算量剧增和单一构件响应量作为优化目标优化效果不理想的问题,借助响应面方法提高最优解搜索效率,提出了以桥梁结构在E2水平设防地震下的震后维修费用为优化目标的减隔震参数优化方法。首先对基于构件的桥梁结构震后直接经济损失计算方法和结合中心复合设计的响应面方法进行了介绍;然后以一座设置拉索模数伸缩缝和板式橡胶支座的斜交连续梁桥为例,构建基于OpenSees数值平台的非线性有限元模型,选取与规范反应谱相匹配的原场地震动时程作为输入,对板式橡胶支座的刚度、拉索模数伸缩缝的自由程和拉索刚度进行了优化设计,验证所提方法的正确性和可靠性;最后建立了不同斜交角下分别采用拉索模数伸缩缝和普通模数伸缩缝的斜交桥模型,对比分析了拉索模数伸缩缝的减震效果。结果表明:所提的斜交桥减隔震参数优化方法具有较好的计算效率和准确性;斜交桥震后维修花费受支座刚度的影响最大,拉索自由程次之,受拉索刚度的影响最小;拉索模数伸缩缝的设置可以平衡支座损伤和桥台损伤,使桥梁的震后维修费用显著减少;设置普通模数伸缩缝的斜交桥,其震后维修费用随斜交角的增大而增加,而设置拉索模数伸缩缝的斜交桥,其震后维修费用受斜交角影响较小。

Abstract

The computational cost of the existing optimization methods for the parameters of seismic isolation devicesin practical engineering project would dramatically become higher if the number of parameters increases. Meanwhile, some of the previous relevant studies only select one response parameter of structural components as the optimization target, which usually leads to limited optimized outcomes. Along these lines, the repair costs of the bridge under the E2 level earthquake are taken as the optimization goal, and the response surface method which can improve the search efficiency of the optimization is used to optimize the design parameters of the seismic isolation devices. Firstly, the component-based seismic loss assessment method and the response surface method combined with the central composite design were introduced. Secondly, a continuous skew girder bridge equipped with rubber bearings and cable-sliding modular expansion joints was taken as a case-study, and its numerical model was built using OpenSees platform. Then the ground motions matching the standard response spectra were selected as input, and the bearing stiffness, the slack length of the cable as well as the cable stiffness were optimized according to the proposed parameter optimization method. Finally, skew bridge models with cable-sliding modular expansion joints and ordinary modular expansion joints with different skew angles were established, and the damping effects of the cable-sliding modular expansion jointwere comparatively assessed. Results show that the proposed optimization method has high calculation efficiency and accuracy. The seismic repair cost of skew bridges is most affected by the stiffness of bearings, followed by the slack length of the cable, and the cable stiffness. The installation of the cable-sliding modular expansion joints could balance the damage of bearings and abutments, as a result, the bridge repair costs are significantly reduced. Repair costs of skew bridges with ordinary modular expansion joints increase with the increase of the skew angle while the losses of the oneswith cable-sliding modular expansion joints are less affected by the skew angle.

关键词

桥梁工程 / 参数优化 / 响应面法 / 斜交桥 / 地震损失 / 减隔震

Key words

bridge engineering / parameter optimization / response surface method / skew bridges / seismic loss / seismic mitigation and isolation

引用本文

导出引用
张鹏辉,冯睿为,郭军军,袁万城. 采用拉索模数伸缩缝的斜交桥减隔震参数优化[J]. 振动与冲击, 2022, 41(9): 120-127
ZHANG Penghui, FENG Ruiwei, GUO Junjun, YUAN Wancheng. Optimization of seismic mitigation and isolation parameters of skew bridge with cable modulus expansion joint[J]. Journal of Vibration and Shock, 2022, 41(9): 120-127

参考文献

[1] 李建中, 袁万城, 范立础. 连续梁桥减、隔震体系的优化设计 [J]. 土木工程学报, 1998, 31(3): 47-54.
LI Jian-zhong, YUAN Wan-cheng, FAN Li-chu. Optimum design of continuous girder bridge seismic isolation system [J]. China Civil Engineering Journal, 1998, 31(3): 47-54.
[2] 梁瑞军, 王浩, 郑文智, 等. 隔震曲线连续梁桥铅芯橡胶支座参数优化 [J]. 工程力学, 2019, 36(11): 83-90.
LIANG Rui-jun, WANG Hao, ZHENG Wen-zhi, et al. Parameter optimization of lead rubber bearings of an isolated curved girder bridge [J]. Engineering Mechanic, 2019, 36(11): 83-90.
[3] 杨风利, 钟铁毅, 夏禾. 铁路简支梁桥减隔震支座设计参数的优化研究 [J]. 铁道学报, 2006, 28(3): 128-132.
YANG Feng-li, ZHONG Tie-yi, XIA He. Study on optimization of the design parameter of seismic absorption and isolation bearing for railway simple supported beam bridges [J]. Journal of the China Railway Society, 2006, 28(3): 128-132.
[4] NIGDELI S M, BEKDAŞ G, ALHAN C. Optimization of seismic isolation systems via harmony search [J]. Engineering Optimization, 2014, 46(11): 1553-1569.
[5] XU Z-D, GUO Y-F, WANG S-A, et al. Optimization analysis on parameters of multi-dimensional earthquake isolation and mitigation device based on genetic algorithm [J]. Nonlinear Dynamics, 2013, 72(4): 757-765.
[6] MOEINDARBARI H, TAGHIKHANY T. Novel procedure for reliability-based cost optimization of seismically isolated structures for the protection of critical equipment: A case study using single curved surface sliders [J]. Structural Control and Health Monitoring, 2018, 25(1): e2054.
[7] ÇERçEVIK A E, AVŞAR Ö, HASANçEBI O. Optimum design of seismic isolation systems using metaheuristic search methods [J]. Soil Dynamics and Earthquake Engineering, 2020, 131: 106012.
[8] PARK K-S, JUNG H-J, LEE I-W. A comparative study on aseismic performances of base isolation systems for multi-span continuous bridge [J]. Engineering Structures, 2002, 24(8): 1001-1013.
[9] 孙臻, 刘伟庆, 王曙光, 等. 基于整体可靠度的隔震结构参数优化分析 [J]. 振动与冲击, 2013, 32(12): 6-10+21.
SUN Zhen, LIU Wei-qing, WANG Shu-guang, et al. Parametric optimization of a base-isolated structure based on system reliability [J]. Journal of Vibration and Shock, 2013, 32(12): 6-10+21.
[10] ZHONG J, HU Z, YUAN W, et al. System-based probabilistic optimization of fluid viscous dampers equipped in cable-stayed bridges [J]. Advances in Structural Engineering, 2018, 21(12): 1815-1825.
[11] XIE Y, ZHANG J. Design and Optimization of Seismic Isolation and Damping Devices for Highway Bridges Based on Probabilistic Repair Cost Ratio [J]. Journal of Structural Engineering, 2018, 144(8): 04018125.
[12] MACKIE K R, STOJADINOVIĆ B. Performance-based seismic bridge design for damage and loss limit states [J]. Earthquake Engineering & Structural Dynamics, 2007, 36(13): 1953-1971.
[13] ZHANG J, HUO Y. Evaluating effectiveness and optimum design of isolation devices for highway bridges using the fragility function method [J]. Engineering Structures, 2009, 31(8): 1648-1660.
[14] BRADLEY B A, CUBRINOVSKI M, DHAKAL R P, et al. Probabilistic seismic performance and loss assessment of a bridge–foundation–soil system [J]. Soil Dynamics and Earthquake Engineering, 2010, 30(5): 395-411.
[15] BASOZ N, KIREMIDJIAN A S, Evaluation of bridge damage data from the Loma Prieta and Northridge, California earthquakes [R]. Buffalo, NY: Multidisciplinary Center for Earthquake Engineering Research, 1998.
[16] MACKIE K R, WONG J M, STOJADINOVIĆ B. Post‐earthquake bridge repair cost and repair time estimation methodology [J]. Earthquake Engineering & Structural Dynamics, 2010, 39(3): 281-301.
[17] GHOSH J, PADGETT J E. Probabilistic seismic loss assessment of aging bridges using a component‐level cost estimation approach [J]. Earthquake Engineering & Structural Dynamics, 2011, 40(15): 1743-1761.
[18] KAMESHWAR S, PADGETT J E. Characterizing and Predicting Seismic Repair Costs for Bridges [J]. Journal of Bridge Engineering, 2017, 22(11): 04017083.
[19] NIELSON B G, DESROCHES R. Analytical seismic fragility curves for typical bridges in the central and southeastern United States [J]. Earthquake Spectra, 2007, 23(3): 615-633.
[20] BAYAT M, DANESHJOO F, NISTICò N, et al. Seismic evaluation of isolated skewed bridges using fragility function methodology [J]. Computers and Concrete, 2017, 20(4): 419-427.
[21] JEON J-S, SHAFIEEZADEH A, LEE D H, et al. Damage assessment of older highway bridges subjected to three-dimensional ground motions: Characterization of shear–axial force interaction on seismic fragilities [J]. Engineering Structures, 2015, 87: 47-57.
[22] BOX G E P, WILSON K B. On the Experimental Attainment of Optimum Conditions [J]. Journal of the Royal Statistical Society: Series B (Methodological), 1951, 13(1): 1-38.
[23] JT/T 663-2006. 公路桥梁板式橡胶支座规格系列[S]. 北京: 人民交通出版社, 2007.
JT/T 663-2006. Specification series of highway bridge laminated rubber bearings [S]. Beijing: China Communications Press, 2007.
[24] GAO K, YUAN W, CAO S, et al. Seismic performance of cable-sliding modular expansion joints subject to near-fault ground motion [J]. Latin American Journal of Solids and Structures, 2015, 12(7): 1397-1414.
[25] GAO K, YUAN W C, DANG X Z. Development and experimental study on cable-sliding modular expansion joints [J]. Structural Engineering and Mechanics, 2017, 61(6): 795-806.
[26] ASCE/SEI 7-05. Minimum design loads for buildings and other structures[S]. Reston, VA: ASCE, 2006.
[27] BOMMER J J, ACEVEDO A B. The use of real earthquake accelerograms as input to dynamic analysis [J]. Journal of Earthquake Engineering, 2004, 8(1): 43-91.
[28] WATSON-LAMPREY J, ABRAHAMSON N. Selection of ground motion time series and limits on scaling [J]. Soil Dynamics and Earthquake Engineering, 2006, 26(5): 477-482.
 

PDF(2467 KB)

269

Accesses

0

Citation

Detail

段落导航
相关文章

/