为准确探究横向振动工况下螺栓连接的松动特性, 本文综合考虑了局部滑移与扭矩滑移的影响，建立了考虑惯性力的螺栓连接模型,对螺纹周向不同位置进行受力分析，得到了计算螺栓临界松动载荷的理论计算方法，并利用横向振动试验进行了验证，结果表明该理论计算方法具有更高的准确性。定量计算了不同预紧力、螺纹面摩擦系数、振动次数、螺距、振动频率、螺纹升角等参数下的螺栓临界松动载荷，揭示了螺栓松动的主要影响因素。当增大预紧力、螺纹面摩擦系数，降低振动次数、螺距、振动频率和螺纹升角时，螺栓临界松动载荷随之增大，有利于提高螺栓连接抵抗自松弛的防松能力。研究结果对螺栓连接防松设计具有指导意义。
Abstract
In order to accurately explore the loosening characteristics of bolt connection under transverse vibration conditions, this paper comprehensively considered the influence of local slip and torque slip, established a bolt connection model considering inertial force, analyzed the forces at different positions of the screw threads, and obtained a theoretical calculation method for calculating the critical loosening load of bolts, which is verified by the transverse vibration test. The results show that the theoretical calculation method has higher accuracy. The critical loosening load of bolts under different parameters such as preload, friction coefficient of thread surface, vibration number, pitch, vibration frequency and thread rise angle is quantitatively calculated, and the main influencing factors of bolt loosening are revealed. When the preload and friction coefficient of thread surface are increased and the vibration number, pitch, vibration frequency and thread rise Angle are reduced, the critical loosening load of bolts will increase, which is conducive to improving the anti-loosening ability of bolt connection against self-loosening. The research results have a guiding significance for the design of bolt-joint locking.
关键词
螺栓连接 /
横向振动 /
惯性力 /
临界松动载荷 /
数值计算
{{custom_keyword}} /
Key words
Bolted connection /
Transverse vibration /
Inertial force /
Critical loosening load /
Numerical calculation
{{custom_keyword}} /
{{custom_sec.title}}
{{custom_sec.title}}
{{custom_sec.content}}
参考文献
[1] Hao GONG, Xiaoyu DING, Jianhua LIU, Huihua FENG. Review of research on loosening of threaded fasteners[J].Friction,2022,10(03):335-359.
[2] Bickford J H. An Introduction to the Design and Behavior of Bolted Joints. 3rd ed. New York (USA): Marcel Dekker Inc., 1995.
[3] Hossein TOWSYFYAN, Fengshou GU, Andrew D BALL, Bo LIANG. Tribological behaviour diagnostic and fault detection of mechanical seals based on acoustic emission measurements[J].Friction,2019,7(06):572-586.
[4] Sweeney R. J. Goodier J N, Loosening by vibration of threaded fastening, Mechanical Engineering,1945, 67, 798-802
[5] N.G. Pai, D.P. Hess, Experimental study of loosening of threaded fasteners due to dynamic shear loads, Journal of sound and vibration, 2002, 253(3): 585-602
[6] N.G. Pai, D.P. Hess, Three-dimensional finite element analysis of threaded fastener loosening due to dynamic shear load[J]. Engineering Failure Analysis, 2002, 9(4):383-402.
[7] Jiang Y , Ming Z , Park T W , et al. An Experimental Study of Self-Loosening of Bolted Joints[J]. Journal of Mechanical Design, 2004, 126(5):925-931.
[8] IZUMI S，YOKOYAMA T，IWASAKI A. Three- dimensional finite element analysis of tightening and loosening mechanism of threaded fastener[J]. Engineering Failure Analysis，2005，12(4)：604-615.
[9] ZHANG M，JIANG Y，LEE C. Finite element modeling of self-loosening of bolted joints[J]. Journal of Mechanical Design，2007，129(2)：218-226.
[10] 张明远,鲁连涛,唐明明，等. 横向载荷作用下螺栓临界松动载荷数值计算方法研究[J].机械工程学报,2018,54(05):173-178.
ZHANG Mingyuan, LU Liantao, TANG Mingming, et al. Research on Numerical Method of Critical Loosening Load of Bolt under Lateral Load [J]. Chinese Journal of Mechanical Engineering,2018,54(05):173-178.
[11] Eccles W , Sherrington I , Arnell R D . Towards an understanding of the loosening characteristics of prevailing torque nuts[J]. ARCHIVE Proceedings of the Institution of Mechanical Engineers Part C Journal of Mechanical Engineering Science 1989-1996 (vols 203-210), 2010, 224(2):483-495.
[12] MOTOSH N.. Development of Design Charts for Bolts Preloaded up to the Plastic Range[J]. Journal of Engineering for Industry,1976,98(3).
[13] Sakai T. Effect of friction coefficient on screw thread loosening in automobiles[J]. Japanese Journal of Tribology, 2001(6):46.
[14] Wright K. An investigation of fretting corrosion[J]. Proceedings of the Institution of Mechanical Engineers. 1953, 167(1b): 556-574.
[15] 陈维金.德国与我国机车车辆用螺栓技术的对比分析[J].铁道技术监督.2011,39(4):2-7.
CHEN Weijin. Comparative Analysis of Bolt Technology for Locomotive and Rolling Stock in Germany and China [J]. Railway Technical Supervision, 2011,39(4):2-7.
[16] 刘盛循. 紧固件横向振动防松机理研究[D].上海交通大学,2020.DOI:10.27307/d.cnki.gsjtu.2020.000840.
{{custom_fnGroup.title_cn}}
脚注
{{custom_fn.content}}
PDF(1545 KB)
