采用UHPC连接的插槽式预制拼装桥墩抗震性能试验研究

李立峰1, 2, 赵智1, 唐嘉豪1, 王柠1

振动与冲击 ›› 2025, Vol. 44 ›› Issue (2) : 210-220.

PDF(2678 KB)
PDF(2678 KB)
振动与冲击 ›› 2025, Vol. 44 ›› Issue (2) : 210-220.
地震科学与结构抗震

采用UHPC连接的插槽式预制拼装桥墩抗震性能试验研究

  • 李立峰*1,2,赵智1,唐嘉豪1,王柠1
作者信息 +

Experimental study on the seismic performance of prefabricated piers connected by UHPC

  • LI Lifeng*1,2,ZHAO Zhi1,TANG Jiahao1,WANG Ning1
Author information +
文章历史 +

摘要

利用UHPC材料特性,提出一种针对预制拼装桥墩的重力灌浆构造,即采用UHPC灌浆并依靠立柱自身重力完成拼接的插槽式连接构造。为研究该形式桥墩的抗震性能,设计完成了三个桥墩的拟静力试验,分别为整体现浇墩Z1、新型插槽式连接墩P1及现有“I型”连接墩P2,并采用OpenSees有限元软件做模拟分析,与试验结果对比分析。结果表明:三个桥墩的破坏形式一致,均为弯曲破坏;Z1墩与P1墩滞回曲线呈梭形,滞回环较为饱满,且相同位移加载循环下的滞回路径较为吻合,P2墩接口处钢筋与混凝土间粘结滑移影响较大,导致滞回环面积减小,桥墩整体滞回耗能能力降低;P1墩的耗能能力较Z1墩和P2墩分别提升7%、10.7%,呈现峰值荷载小、失效速率慢、极限位移大、滞回耗能多的骨架趋势。试验结果与有限元模拟结果较为吻合,抗震性能参数差幅在10%以内,新型插槽式连接墩可应用于实际工程。

Abstract

Based on the material characteristics of UHPC, a gravity grouting structure for prefabricated pier is proposed, that is, a slot-type connection structure that uses UHPC grouting and relies on the gravity of the column to complete the splicing. In order to study the seismic performance of this type of pier, the pseudo-static tests of three piers are designed and completed, namely, the monolithic cast-in-place pier Z1, the new slot type connecting pier P1 and the existing "type I" connecting pier P2, and the finite element software OpenSees is used to simulate and analyze the test results. The results show that the failure forms of the three piers are the same, all of them are bending failure. The hysteretic curves of Z1 and P1 piers are fusiform, and the hysteretic loops are relatively full, and the hysteretic paths are more consistent under the same displacement loading cycle. The bonding slip between reinforcement and concrete at the interface of P2 pier has a great influence, resulting in the reduction of the area of the hysteretic loops and the overall hysteretic energy dissipation capacity of the pier. The energy dissipation capacity of P1 pier is 7% and 10.7% higher than that of Z1 pier and P2 pier respectively, showing a skeleton trend of small peak load, slow failure rate, large ultimate displacement and high hysteretic energy consumption. The experimental results are in good agreement with the finite element simulation results, and the seismic performance parameter difference is less than 10%. The new type of slot pier can be applied to practical engineering.

关键词

预制拼装桥墩 / 拟静力试验 / 抗震性能 / UHPC / 连接构造

Key words

Prefabricated pier / Pseudo-static test / Seismic performance / UHPC / Connective construction

引用本文

导出引用
李立峰1, 2, 赵智1, 唐嘉豪1, 王柠1. 采用UHPC连接的插槽式预制拼装桥墩抗震性能试验研究[J]. 振动与冲击, 2025, 44(2): 210-220
LI Lifeng1, 2, ZHAO Zhi1, TANG Jiahao1, WANG Ning1. Experimental study on the seismic performance of prefabricated piers connected by UHPC[J]. Journal of Vibration and Shock, 2025, 44(2): 210-220

参考文献

[1] 刘斌,黄永福,宋彦臣,等.高烈度区波纹管连接预制拼装桥墩抗震性能研究[J].振动与冲击,2024,43(02):123-137.
LIU Bin, HUANG Yongfu, SONG Yanchen,et al. Seismic performance of prefabricated assembled piers connected with corrugated pipes in high intensity seismic areas[J]. Journal of vibration and shock, 2024, 43 (02): 123-137.
[2] 欧智菁,颜建煌,俞杰,等.装配式圆钢管约束混凝土桥墩抗震性能研究[J].振动与冲击,2022,41(18):47-54.
OU Zhijing, YAN Jianhuang, YU Jie,et al. Seismic Performance of fabricated circular steel tube confined concrete piers[J]. Journal of vibration and shock, 2022, 41(18): 47-54.
[3] 李辰,江辉,郭辉等.组合式剪力键预制拼装桥墩结构及其抗震性能研究[J].振动与冲击,2021,40(20):117-126+142.
[4] LI Chen, JIANG Hui, GUO Hui,et al. Precast segmental bridge pier structure with combined shear keys and seismic performance analysis[J]. Journal of vibration and shock, 2021, 40 (20): 117-126+142.
[5] 叶爱君,管仲国.桥梁抗震(第三版)[M].上海:人民交通出版社,2017.
[6] 石岩,李军,秦洪果,等.桥梁双柱式排架墩抗震性能研究进展述评[J].中国公路学报,2021,34(02):134-154.
SHI Yan, LI Jun, QIN Hongguo,et al. Review on Seismic Performance of Bridge Double-column Bents[J]. China Journal of Highway and Transport, 2021, 34(02): 134-154.
[7] 陈彦江,丁梦佳,许维炳,等.预制拼装桥墩体系及其抗震性能研究进展[J].中国公路学报,2022,35(12):56-76.
CHEN Yanjiang, DING Mengjia, XU Weibing,et al. Research Process for Seismic Performance of the Prefabricated Concrete Pier System[J]. China Journal of Highway and Transport, 2022, 35(12): 56-76.
[8] 韩强,董慧慧,王利辉,等.基于可更换构件的可恢复功能桥梁防震结构研究综述[J].中国公路学报,2021,34 (09):215-230.
HAN Qiang, DONG Huihui, WANG Lihui,et al. Review of Seismic Resilient Bridge Structures with Replaceable Members[J]. China Journal of Highway and Transport, 2021, 34(09): 215-230.
[9] 石岩,李军,秦洪果,等.桥梁双柱式排架墩抗震性能研究进展述评[J].中国公路学报,2021,34(02):134-154.
SHI Yan, LI Jun, QIN Hongguo,et al. Review on Seismic Performance of Bridge Double-column Bents[J]. China Journal of Highway and Transport, 2021, 34(02): 134-154.
[10] 王景全,王震,高玉峰,等.预制桥墩体系抗震性能研究进展:新材料、新理念、新应用[J].工程力学,2019,36(03):1-23.
WANG Jingquan, WANG Zhen, GAO Yufeng,et al. Review on aseismic behavior of precast piers: new material, new concept, and new application[J]. Engineering mechanics, 2019, 36(03): 1-23.
[11] Chen Jun, Chen Xulin, Ding Faxing,et al. Mechanical performance of overlap connections with grout-filled anchor reinforcements in embedded metal corrugated pipe[J]. Archives of Civil and Mechanical Engineering, 2020, 20(4): 128.
[12] Chen Jun, Zhao Chenhui, Ding Faxing,et al. Mechanical performance of the grouted lapped double reinforcements anchored in embedded corrugated sleeves[J]. Structures, 2020, 28: 1354-1365.
[13] 徐艳,曾增,王志强,等.承插式桥墩连接构造及其力学行为的研究进展[J].土木工程学报,2023,56(01):90-108.
XU Yan, ZENG Zeng, Wang Zhiqiang,et al. Review of the state-of-the-art of the configurations and mechanical behaviors of piers with socket connections[J]. China Civil Engineering Journal, 2023, 56(01): 90-108.
[14] ZHANG G, HAN Q, XU K,et al. Quasi-static test of CFST embedded RC column-to-precast cap beam with socket connection[J]. Engineering Structures, 2021, 241:112443.
[15] 刘雪山,李建中,张宏杰,等.不同构造下的预制拼装钢管混凝土桥墩抗震性能试验[J].中国公路学报,2021,34 (11):116-128.
LIU Xueshan, LI Jianzhong, ZHANG Hongjie,et al. Experimental analysis of seismic performance of precast assembled concrete filled steel tube piers under different structures[J]. China Journal of Highway and Transport, 2021, 34(11): 116-128.
[16] LI Tiantian, QU Hongya, WANG Zhiqiang,et al. Seismic performance of precast concrete bridgecolumns with quasi-static cyclic shear test for high seismic zones[J]. Engineering Structures, 2018, 166(1): 13-27.
[17] 胡志坚,闫明辉,周知,等.预制拼装桥墩地震易损性分析[J].土木工程学报,2022,55(01):89-99+108.
HU Zhijian, YAN Minghui, ZHOU Zhi,et al. Seismic vulnerability analysis of precast segmental bridge piers[J]. China Civil Engineering Journal, 2022, 55(01): 89-99+108.
[18] MATSUMOTO E E. Emulative precast bent cap connections for seismic regions: componenttests-cap pocket full ductility specimen[R]. Sacramento: California State University, 2009.
[19] WANG Z, LI T, QU H,et al. Seismic performance of precast bridge columns with socket and pocket connections based on quasi-static cyclic tests: Experimental and numerical study[J]. Journal of Bridge Engineering, 2019, 24(11): 4019105
[20] 吴平平,周小伍,汪志甜等.插槽结构装配式桥墩足尺模型拟静力试验研究[J].桥梁建设,2020.50(03):76-80.
WU Pingping, ZHOu Xiaowu, WANG Zhitian,et al. Full-scale model quasi-static test for modular pier with socket connection[J]. Bridge construction, 2020. 50(03): 76-80.
[21] 邵旭东,樊伟,黄政宇.超高性能混凝土在结构中的应用[J].土木工程学报,2021,54(01):1-13.
SHAO Xudong, FAN Wei, HUANG Zhenyu. Application of Ultra-High-Performance Concrete in engineering Structures[J]. China Civil Engineering Journal, 2021, 54(01): 1-13.
[22] 邵旭东,邱明红,晏班夫,等.超高性能混凝土在国内外桥梁工程中的研究与应用进展[J].材料导报,2017,31(23):33-43.
SHAO Xudong, QIU Minghong, YAN Banfu,et al. A Review on the Research and Application of Ultra-high Performance Concrete in Bridge Engineering Around the World[J]. Material Reports Journal Profile. 2017, 31(23): 33-43.
[23] SALEEM M A, MIRMIRAN A, XIA J,et al. Development length of high-strength steelrebar in ultrahigh performance concrete[J]. Journal of Materials in Civil Engineering, 2013, 25(8): 991-998.
[24] YAMANOBE S, SAITO K, ICHINOMIYA T,et al. Bilateral loading experiment on and analysis of concrete piers using mortar-jointed ultra- high-strength fiber-reinforced concrete precast formwork[J]. Structural Concrete, 2013,14(3): 278-290.
[25] TAZARV M, SAIIDI M S. UHPC-filled duct connections for accelerated bridge construction of RC columns in high seismic zones[J]. Engineering Structures, 2015, 99: 413-422.
[26] SPACONE e, FILIPPOU F C, TAUCER F F. (1996), Fibre beam–column model for non-linear analysis of RC frames: part I formulation. Earthquake Engineering, Structural Dynamics, 25: 711-725.
[27] 禚一,李忠献.钢筋混凝土纤维梁柱单元实用模拟平台[J].工程力学,2011,28(04):102-108+127.
ZHUO Yi, LI Zhongxian, A practical simulation platform of reinforced concrete fiber beam-column element[J]. Engineering mechanics, 2011, 28(04): 102-108+127.
[28] KENT D C, PARK R. Flexural Members with Confined Concrete[J]. Journal of the Structural Division. 1971, 97 (ST7): 1969-1990.
[29] 张耀庭,赵璧归,李瑞鸽等.HRB400钢筋单调拉伸及低周疲劳性能试验研究[J].工程力学,2016,33(04):121-129.
ZHANG Yaoting, ZHAO Bigui, LI Ruige,et al. Monotonic and low cycle fatigue tension and research for HRB400 steel[J]. Engineering mechanics, 2016, 33(04): 121-129.
[30] ZHAO J, SRITHARAN S. Modeling of strain penetration effects in fiber-based analysis of reinforced concrete structures[J]. ACI Materials Journal, 2007, 104(2): 133−141.
[31] 熊能,顾冬生.钢筋粘结滑移弯矩-转角计算模型[J].工程力学,2019,36(12):98-105.
XIONG Neng, GU Dongsheng. A Calculation model for the slip moment-rotation of reinforcement bond[J]. Engineering mechanics, 2019, 36(12): 98-105.
[32] 雷拓,钱江,刘伯权.考虑非线性剪切效应的钢筋混凝土柱模型化方法及应用[J].土木建筑与环境工程, 2013, 35(04): 13-19.
LEI Tuo, QIAN Jiang, LIU Boquan. Modeling and its application of reinforced concrete columns considering nonlinear shear effects[J]. Civil building and environmental engineering, 2013, 35(04): 13-19.

PDF(2678 KB)

Accesses

Citation

Detail

段落导航
相关文章

/