铆钉布置对搭接接头强度的影响及优化设计

PDF(4253 KB)

振动与冲击 ›› 2023, Vol. 42 ›› Issue (17) : 253-264.

论文

铆钉布置对搭接接头强度的影响及优化设计

韩昊兵1，徐文涛1，卿华2，任柯融2,3

作者信息 +

Effects of rivet arrangement on strength of lap joint and its optimization design

HAN Haobing1, XU Wentao1, QING Hua2, REN Kerong2,3

Author information +

文章历史 +

摘要

针对铆钉布置对铆接搭接接头强度的影响问题，首先通过有限元方法研究了铆接搭接接头的失效模式及失效机理，其次以峰值荷载为指标研究了铆钉数量、铆钉行数、铆钉布置、铆钉行距对搭接强度的影响，以线荷载集度为指标，研究了铆钉间距与铆钉边距对搭接强度的影响，并建立力学模型研究多排铆钉的受力情况，最后基于响应面法对铆钉布置进行优化。结果表明：当采用多行铆钉布置时，外侧铆钉数较多的一行由于应力集中程度高会首先发生断裂，铆钉布置应采用中间多两边少的布置方式;当铆钉总强度大于板材剩余强度时，铆钉数量和铆钉行数对搭接强度的影响有限，其主要影响搭接构件的破坏形式。响应面优化结果表明：当边距=3.4d、铆距=5.3d、行距=3.4d时搭接强度最高。研究成果对飞机铆接结构的强度提高具有重要意义。

Abstract

To address the issue of the effect of rivet arrangement on the strength of riveted lap joints, the failure mode and failure mechanism of riveted lap joints were first studied by LS-DYNA. Secondly, the effects of the number of rivets, rivet rows, rivet arrangement and rivet row spacing on the lap joint strength were studied using the peak load as the index, and the effects of rivet spacing and rivet edge distance on the lap joint strength were studied using the linear load concentration. A mechanical model is also developed to study the stresses on multiple rows of rivets. Finally, the rivet arrangement is optimized based on the Response Surface Methodology. The results show that when multiple rivet lines are used, the outer rivet line with more rivets will break first due to high stress concentration, and the rivet arrangement should be arranged in a way that there are more rivets in the middle and fewer rivets on both sides. When the total rivet strength is greater than the residual strength of the plate, the number of rivets and rivet rows have limited effect on the lap joint strength, which mainly affects the damage form of the lap joint member. The response surface optimization results show that the lap joint strength is highest when the edge spacing = 3.4d, rivet spacing = 5.3d, and row spacing = 3.4d. The research results are of great significance to the strength improvement of the riveted structures of aircraft.

导出引用

韩昊兵1，徐文涛1，卿华2，任柯融2,3. 铆钉布置对搭接接头强度的影响及优化设计[J]. 振动与冲击, 2023, 42(17): 253-264

HAN Haobing1, XU Wentao1, QING Hua2, REN Kerong2,3. Effects of rivet arrangement on strength of lap joint and its optimization design[J]. Journal of Vibration and Shock, 2023, 42(17): 253-264

参考文献

[1] CHERAGHI S H. Effect of variations in the riveting process on the quality of riveted joints[J]. International Journal of Advanced Manufacturing Technology, 2008, 39(11-12): 1144-55.
[2] PRIJANOVIC U, TONKOVIC M P, TRDAN U, et al. Remote Fibre Laser Welding of Advanced High Strength Martensitic Steel[J]. Metals, 2020, 10(4): 14.
[3] ZHENG B, YU H D, LAI X M. Assembly deformation prediction of riveted panels by using equivalent mechanical model of riveting process[J]. International Journal of Advanced Manufacturing Technology, 2017, 92(5-8): 1955-66.
[4] CAO Z Q, ZUO Y J. Electromagnetic riveting technique and its applications[J]. Chinese Journal of Aeronautics, 2020, 33(1): 5-15.
[5] HAMEL V, ROELANDT J M, GACEL J N, et al. Finite element modeling of clinch forming with automatic remeshing[J]. Computers & Structures, 2000, 77(2): 185-200.
[6] DE PAULA A A, AGUILAR M T P, PERTENCE A E M, et al. Finite element simulations of the clinch joining of metallic sheets[J]. Journal of Materials Processing Technology, 2007, 182(1-3): 352-7.
[7] TENORIO M B, LAJARIN S F, GIPIELA M L, et al. The influence of tool geometry and process parameters on joined sheets by clinching[J]. Journal of the Brazilian Society of Mechanical Sciences and Engineering, 2019, 41(2): 11.
[8] ZHANG X, YU H P, SU H, et al. Experimental evaluation on mechanical properties of a riveted structure with electromagnetic riveting[J]. International Journal of Advanced Manufacturing Technology, 2016, 83(9-12): 2071-82.
[9] CUI J J, QI L, JIANG H, et al. Numerical and experimental investigations in electromagnetic riveting with different rivet dies[J]. International Journal of Material Forming, 2018, 11(6): 839-53.
[10] SKORUPA M, SKORUPA A, MACHNIEWICZ T, et al. Effect of production variables on the fatigue behaviour of riveted lap joints[J]. Int J Fatigue, 2010, 32(7): 996-1003.
[11] AMAN F, CHERAGHI S H, KRISHNAN K K, et al. Study of the impact of riveting sequence, rivet pitch, and gap between sheets on the quality of riveted lap joints using finite element method[J]. International Journal of Advanced Manufacturing Technology, 2013, 67(1-4): 545-62.
[12] LI D, HAN L, THORNTON M, et al. Influence of edge distance on quality and static behaviour of self-piercing riveted aluminium joints[J]. Materials & Design, 2012, 34: 22-31.
[13] LI D Z, HAN L, THORNTON M, et al. Influence of rivet to sheet edge distance on fatigue strength of self-piercing riveted aluminium joints[J]. Materials Science and Engineering a-Structural Materials Properties Microstructure and Processing, 2012, 558: 242-52.
[14] 姚卫星. 结构疲劳寿命分析[M]. 北京：国防工业出版社, 2003:6-8.
YAO W X. Structural fatigue life analysis[M]. Beijing: National Defense Industry Press, 2003:6-8 (in Chinese).
[15] MCCARTHY M A, LAWLOR V P, STANLEY W F. An experimental study of bolt-hole clearance effects in single-lap, multibolt composite joints[J]. J Compos Mater, 2005, 39(9): 799-825.
[16] MCCARTHY M A, MCCARTHY C T, LAWLOR V P, et al. Three-dimensional finite element analysis of single-bolt, single-lap composite bolted joints: part I - model development and validation[J]. Compos Struct, 2005, 71(2): 140-58.
[17] 蒋持平, 张行. 多钉连接件钉传载荷计算的一个解析方法[J]. 航空学报, 1994, (03): 310-7.
JIANG C P, ZHANG X. An analytical method of pin load computations for joints with multi-fasteners[J]. Acta Aeronautica et Astronautica Sinica, 1994, (03): 310-7 (in Chinese).
[18] 张天宇, 何宇廷, 陈涛, 等. 一种多钉铆接连接件的疲劳寿命分析方法[J]. 北京航空航天大学学报, 2018, 44(9): 8.
ZHANG T Y, HE Y T, CHEN T, et al. A fatigue life analysis method for multiple riveted joint[J]. Journal of Beijing University of Aeronautics and Astronautics, 2018, 44(9): 8 (in Chinese).
[19] GRAY P J, O'HIGGINS R M, MCCARTHY C T. Effects of laminate thickness, tapering and missing fasteners on the mechanical behaviour of single-lap, multi-bolt, countersunk composite joints[J]. Composite Structures, 2014, 107: 219-30.
[20] 黄庆概. 单搭接件力学性能研究[D]. 浙江：浙江大学, 2016:10-15.
HUANG Q G. Research on mechanical properties of single-lap joint[D]. Zhejiang: Zhejing University, 2016:10-15 (in Chinese).
[21] LIU J T, ZHAO A A, KE Z Z, et al. Influence of Rivet Diameter and Pitch on the Fatigue Performance of Riveted Lap Joints Based on Stress Distribution Analysis[J]. Materials, 2020, 13(16): 21.
[22] SUN X, KHALEEL M A. Dynamic strength evaluations for self-piercing rivets and resistance spot welds joining similar and dissimilar metals[J]. International Journal of Impact Engineering, 2007, 34(10): 1668-82.
[23] DONG D Y, SUN L Q, WANG Q, et al. Influence of electromagnetic riveting process on microstructures and mechanical properties of 2A10 and 6082 Al riveted structures[J]x. Archives of Civil and Mechanical Engineering, 2019, 19(4): 1284-94.
[24] ZHANG X, YU H P, LI C F. Multi-filed coupling numerical simulation and experimental investigation in electromagnetic riveting[J]. International Journal of Advanced Manufacturing Technology, 2014, 73(9-12): 1751-63.
[25] Y. Xia, Q. Chen, R. Song. Packing of rectangles using adaptive genetic simulated annealing algorithm[J]. Computer Engineering and Applications, 2018, 54(22):229-32.
[26] Lstc 2018. LS-DYNA®keyword user's manual VolumeⅡ(LS-DYNA R11), [B], Livermore Software Technology Corporation, 2016:143-145.
[27] 张成成, 姚卫星, 叶彬. 连接件疲劳寿命分析的等效SSF法[J]. 航空学报, 2009, 30(2): 5.
ZHANG C C, YAO W X, YE B. Equivalent Stress Severity Factor Approach for Fatigue of Multi -fastener Plate[J]. Acta Aeronautica et Astronautica Sinica, 2009, 30(2): 5 (in Chinese).
[28] OZTURK S, KAHRAMAN M F. Modeling and optimization of machining parameters during grinding of flat glass using response surface methodology and probabilistic uncertainty analysis based on Monte Carlo simulation[J]. Measurement, 2019, 145: 274-91.